ISO 4413-2010 液压流体动力-系统及其元件的一般规则和安全要求

VIP免费

乔大爷开音响 2025-02-07 147 1.08MB 54 页 15星币

侵权投诉

Reference numbe

ISO 4413:2010(E)

INTERNATIONAL

STANDARD

ISO

4413

Third edition

2010-11-15

Hydraulic fluid power — General rules

and safety requirements for systems and

their components

Transmissions hydrauliques — Règles générales et exigences de

sécurité relatives aux systèmes et leurs composants

ISO 4413:2010(E)

PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.

Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.

ISO copyright office

Case postale 56 • CH-1211 Geneva 20

Tel. + 41 22 749 01 11

Fax + 41 22 749 09 47

E-mail copyright@iso.org

Web www.iso.org

Published in Switzerland

ISO 4413:2010(E)

Contents Page

Foreword ............................................................................................................................................................iv

Introduction.........................................................................................................................................................v

1 Scope......................................................................................................................................................1

2 Normative references............................................................................................................................1

3 Terms and definitions ...........................................................................................................................2

4 List of significant hazards ....................................................................................................................3

5 General rules and safety requirements...............................................................................................3

5.1 General ...................................................................................................................................................3

5.2 Basic requirements for the design and specification of hydraulic systems...................................3

5.3 Additional requirements .......................................................................................................................5

5.4 Specific requirements for components and controls........................................................................7

6 Verification of safety requirements and acceptance testing ..........................................................26

7 Information for use..............................................................................................................................26

7.1 General requirements .........................................................................................................................26

7.2 Final information for systems on stationary industrial machinery................................................26

7.3 Maintenance and operating data .......................................................................................................27

7.4 Marking and identification..................................................................................................................28

8 Identification statement (reference to this International Standard) ...............................................30

Annex A (informative) List of significant hazards .........................................................................................31

Annex B (informative) Form for collecting hydraulic system and component data to ensure

conformance with ISO 4413 ...............................................................................................................33

Bibliography......................................................................................................................................................45

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #ISO

摘要：

ISO 4413-2010 是一项国际标准，全称为《液压流体动力-系统及其元件的一般规则和安全要求》，为液压流体动力系统的设计、制造、安装、操作及维护提供了全面的安全准则与技术规范。该标准适用于各类液压系统及其元件，旨在通过统一的风险评估与防护措施，防止因高压液体泄漏、元件失效或操作失误引发的安全事故。内容涵盖系统设计原则、元件选择与集成、管路连接、控制回路、压力限制、温度管理以及维护检查程序等关键环节。遵循 ISO 4413-2010 有助于企业提升设备可靠性、降低故障率并确保符合国际安全法规

展开>> 收起<<

ISO 4413-2010 液压流体动力-系统及其元件的一般规则和安全要求.pdf

共54页,预览4页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ISO 4413-2010 液压流体动力-系统及其元件的一般规则和安全要求

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: