MIL-DTL-32375 (1)

VIP专免

standardshare 2025-06-14 15 248.11KB 25 页 14星币

侵权投诉

MIL-DTL-32375 (MR)

w/AMENDMENT 1

11 December 2012

SUPERSEDING

MIL-DTL-32375 (MR)

29 September 2011

DETAIL SPECIFICATION

ARMOR PLATE, ALUMINUM ALLOY, 7085, UNWELDABLE APPLIQUE

This specification is approved for use by the Department of the Army and is available for

use by all Departments and Agencies of the Department of Defense

1. SCOPE

1.1 Scope. This specification covers 7085 wrought aluminum alloy armor plate for non

fusion welded applications in nominal thicknesses from 0.500 to 3.000 inch, inclusive

(see 6.2). The fusion weldability of 7085 wrought aluminum alloy armor has not been

determined over this thickness range. Therefore, these alloys should only be used as

appliqué armor until a weldability study has been completed.

1.2 Classification. The wrought aluminum armor should be of the following class and

tempers (Types), as specified (see 6.2).

1.2.1 Class I. Wrought aluminum armor that conforms to the Aluminum Association

designation for the 7085 aluminum alloy. The applicable gauge range for Class I is 0.500-

3.000 inches.

1.2.1.1 Type A. Type A has a temper designation of T711 (see 6.3.1) which is a high-

strength temper designed for maximum resistance to armor piercing (AP) projectiles.

1.2.1.2 Type B. Type B has a temper designation of T721 (see 6.3.1) which is designed

for maximum resistance to blast.

Comments, suggestions, or questions on this document should be addressed to: Director,

U.S. Army Research Laboratory, Weapons and Materials Research Directorate, Materials

and Manufacturing Technology Branch, Specifications and Standards Office, Attn:

RDRL-WMM-D, Aberdeen Proving Ground, MD 21005-5069 or emailed to

richard.j.squillacioti.civ@mail.mil. Since contact information can change, you may want

to verify the currency of this address information using the ASSIST Online database at

https://assist.dla.mil/.

AMSC N/A FSC 9535

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

INCH-POUND

Provided by IHS

Licensed by www.sepana.ir

Sale only by www.sepana.ir, 05/21/2014 23:21:51 MDT

No reproduction or networking permitted without license from IHS

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com

MIL-DTL-32375 (MR)

w/AMENDMENT 1

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of

this specification. This section does not include documents cited in other sections of this

specification or recommended for additional information or as examples. While every

effort has been made to ensure the completeness of this list, document users are cautioned

that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of

this specification, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards,

and handbooks form a part of this document to the extent specified herein. Unless

otherwise specified (see 6.2), the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-662 - V50 Ballistic Test for Armor

(Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or

from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D,

Philadelphia, PA 19111-5094.)

2.3 Non-Government publications. The following documents form a part of this

specification to the extent specified herein. Unless otherwise indicated (see 6.2), the

issue in effect on the date of invitation for bids or request for proposal should apply.

SAE INTERNATIONAL

AMS 2750 - Pyrometry

AMS 2772 - Heat Treatment of Aluminum Alloy Raw Materials

(Application for copies should be addressed to SAE International, 400

Commonwealth Drive, Warrendale, PA 15096-0001.)

AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)

ASTM B557 - Standard Test Methods for Tension Testing

Wrought and Cast Aluminum and Magnesium-

Alloy Products

ASTM E34 - Standard Test Methods for Chemical Analysis of

Aluminum and Aluminum-Base Alloys

ASTM E607 - Standard Test Method for Atomic Emission

Spectrometric Analysis of Aluminum Alloys by the

Point-to-Plane Technique, Nitrogen Atmosphere

Provided by IHS

Licensed by www.sepana.ir

Sale only by www.sepana.ir, 05/21/2014 23:21:51 MDT

No reproduction or networking permitted without license from IHS

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com

MIL-DTL-32375 (MR)

w/AMENDMENT 1

ASTM E716 - Standard Practices for Sampling Aluminum and

Aluminum Alloys for Spectrochemical Analysis

ASTM E1251 - Standard Test Method for Analysis of Aluminum

and Aluminum Alloys by Atomic Emission

Spectrometry

(Copies of these documents are available from www.astm.org or ASTM International,

100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.)

2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a

conflict between the text of this document and the references cited herein (except for related

specification sheets), the text of this document takes precedence. Nothing in this document,

however, supersedes applicable laws and regulations unless a specific exemption has been

obtained.

3. REQUIREMENTS

3.1 First article. When specified in the contract or purchase order (see 6.2), first article

testing shall be required and all test samples required by this specification shall be made

available to the contracting officer or his authorized representative for approval in

accordance with 4.3. First article testing shall be completed before production material is

submitted for acceptance testing. The approval of the first article samples authorizes

commencement of production but does not relieve the supplier of the responsibility to

comply with all the applicable provisions of this specification. The first article samples

and acceptance test plates shall be manufactured by the process proposed for use on

production items.

3.2 Chemical composition. The chemical composition of the plates shall be within the

limits shown in Table I. The limits specified in Table I were taken from Aluminum

Association (AA) registered composition limits for Aluminum Alloys. A certification of

conformance of the chemical composition of the alloy shall be furnished with the ballistic

test plates.

3.3 Mechanical properties. Unless otherwise specified in the contract or order (see 6.2),

the mechanical properties of the test specimen taken in the longitudinal direction shall

meet the minimum mechanical properties listed in Table II. If mechanical property

requirements differ from those contained in Table II, or if any other properties are

required, the ballistic requirements shall be negotiated between the procuring activity and

the supplier.

3.4 Ballistic limit. The protection ballistic limit, BL(P), shall be as specified in

Appendix A. When a complete penetration cannot be obtained for any class of armor

material, the following rule shall be in effect until a new ballistic acceptance round can be

developed and utilized. When the ballistic velocities of four (4) partial penetrations are

above the minimum ballistic requirement for the specific thickness, the material shall be

certified as acceptable with a V50 (which obviously cannot be explicitly determined)

above the minimum requirement.

Provided by IHS

Licensed by www.sepana.ir

Sale only by www.sepana.ir, 05/21/2014 23:21:51 MDT

No reproduction or networking permitted without license from IHS

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

摘要：

MIL-DTL-32375 (1) 是美国国防部发布的一项详细规范，主要规定了高性能电连接器的技术要求、测试方法和认证流程。该标准适用于军事和航空航天领域的严苛环境，强调连接器在极端温度、振动、湿度和电磁干扰下的可靠性与耐久性。标准内容涵盖材料选择、镀层要求、机械接口尺寸、电气性能（如接触电阻、绝缘电阻和耐电压）以及环境测试（如盐雾、热冲击和密封性）。版本序号“(1)”表示该规范为首次修订版，可能包含对前版内容的更新或补充，以符合最新的军事装备集成需求。对于从事军用电子设备设计、采购和质量控制的

展开>> 收起<<

MIL-DTL-32375 (1).pdf

共25页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

MIL-DTL-32375 (1)

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: