MIL-STD-188-141D 中频和高频频段的无线电信号系统的设计准则 2017

VIP专免

standardshare 2025-06-16 64 16.09MB 370 页 16星币

侵权投诉

NOT

MEASUREMENT

SENSITIVE

MIL-STD-188-141D

22 December 2017

SUPERSEDING

MIL-STD-188-141C

27 December 2011

DEPARTMENT OF DEFENSE

INTERFACE STANDARD

INTEROPERABILITY AND PERFORMANCE STANDARDS

FOR MEDIUM AND HIGH FREQUENCY

RADIO SYSTEMS

AMSC N/A AREA TCSS

DISTRIBUTION STATEMENT A: Approved for public release; distribution unlimited.

Downloaded from http://www.everyspec.com

MIL-STD-188-141D

FOREWORD

1. This standard is approved for use by all Departments and Agencies of the Department of

Defense (DoD).

2. In accordance with DoD Instruction 4630.8, it is DoD policy that all forces for joint and

combined operations be supported through compatible, interoperable, and integrated Command,

Control, Communications, and Intelligence (C3I) systems. Furthermore, all C3I systems

developed for use by U.S. forces are considered to be for joint use. The director of the Defense

Information Systems Agency (DISA) serves as DoD's single point of contact for developing

information technology standards to achieve interoperability and compatibility. All C3I systems

and equipment shall conform to technical and procedural standards for interface, interoperability,

and compatibility, as recommended by DISA.

3. MIL-STDs in the 188 series (MIL-STD-188-XXX) address telecommunication design

parameters based on proven technologies. These MIL-STDs are to be used in all new DoD

systems and equipment, or major upgrades thereto, to ensure interoperability. The MIL-STD-

188 series is subdivided into a MIL-STD-188-100 series, covering common standards for tactical

and long-haul communications; a MIL-STD-188-200 series, covering standards for tactical

communications only; and a MIL-STD-300 series, covering standards for long-haul

communications only. Emphasis is being placed on the development of common standards for

tactical and long-haul communications (the MIL-STD-188-100 series). The MIL-STD-188

series may be based on, or make reference to, Joint Technical Architecture, American National

Standards Institute (ANSI) standards, International Telecommunications Union (ITU)

recommendations, North Atlantic Treaty Organization (NATO) Standardization Agreements

(STANAG), and other standards wherever applicable.

4. This document contains technical standards and design objectives for medium- and high-

frequency radio systems. Included are: (1) the basic radio parameters to support both

conventional and adaptive radio communications; and (2) technical parameters for automatic link

establishment (ALE), linking protection, and other advanced adaptive features and functions.

5. The technical parameters in certain identified paragraphs have not (as of the date of

publication) been verified by testing or implementation. These parameters have, however, been

subjected to rigorous simulation and computer modeling. The DoD working group and the

Technical Advisory Committee (TAC) are confident that these features, functions, and

parameters are technically valid. The un-tested portion of the technology are marked (NT)

following the title of each paragraph containing un-tested material.

6. Users of this MIL-STD should note that there is no proprietary or otherwise restricted use

material in this document. This document is for unrestricted DoD, federal, and industry use.

7. Comments, suggestions, or questions on this document should be addressed Air Force Sus-

tainment Center – Oklahoma City/AFLCMC/LZPES, 3001 Staff Drive, Suite 1AB81A, Tinker

AFB, OK 73145, or emailed to ocalc.dsp@us.af.mil. Since contact information can change, you

may want to verify the currency of this address information using the ASSIST Online database at

https://assist.dla.mil.

Downloaded from http://www.everyspec.com

MIL-STD-188-141D

iii

CONTENTS

PARAGRAPH PAGE

1. SCOPE. .......................................................................................................................................1

1.1 Scope. ....................................................................................................................................1

1.2 Applicability. ........................................................................................................................1

1.3 Application guidance. ...........................................................................................................1

2. APPLICABLE DOCUMENTS. .................................................................................................1

2.1 General. .................................................................................................................................1

2.2 Government documents. .......................................................................................................1

2.2.1 Specifications, standards, and handbooks. .....................................................................1

2.2.2 Other Government documents, drawings, and publications. .........................................2

2.3 Non-Government publications. .............................................................................................3

2.4 Order of precedence. .............................................................................................................3

3. DEFINITIONS. ...........................................................................................................................4

3.1 Terms. ...................................................................................................................................4

3.2 Abbreviations and acronyms. ...............................................................................................5

4. GENERAL REQUIREMENTS. .................................................................................................6

4.1 General. .................................................................................................................................6

4.1.1 Equipment parameters....................................................................................................6

4.1.2 Basic HF radio parameters. ............................................................................................6

4.2 Equipment operation mode. ..................................................................................................8

4.2.1 Baseline mode. ...............................................................................................................8

4.2.2 Manual mode push-to-talk operation. ............................................................................8

4.2.3 ALE mode. .....................................................................................................................9

4.2.4 Anti-jam (AJ) mode. ......................................................................................................9

4.2.5 Linking protection (LP). ................................................................................................9

4.3 Interface parameters. .............................................................................................................9

4.3.1 Electrical characteristics of digital interfaces. ...............................................................9

4.3.2 Electrical characteristics of analog interfaces. ...............................................................9

4.4 NATO and Quadripartite interoperability requirements. ......................................................9

4.4.1 Single-channel communications systems.......................................................................9

4.4.2 Maritime air communications systems. .........................................................................9

4.4.3 High-performance HF data modems. .............................................................................9

4.4.4 QSTAGs. ......................................................................................................................10

4.5 Adaptive communications. .................................................................................................10

4.6 Linking protection. ..............................................................................................................10

4.7 HF data link protocol. .........................................................................................................10

4.8 Networking functions. ........................................................................................................10

4.9 HF e-mail and other application protocols for HF radio networks. ....................................10

Downloaded from http://www.everyspec.com

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #设计准则

摘要：

本规范文档标题为《MIL-STD-188-141D 中频和高频频段的无线电信号系统的设计准则 2017》，涵盖了美国国防部针对中频（MF）和高频（HF）频段无线电通信系统的最新设计标准与技术要求。该标准于2017年发布，是MIL-STD-188-141系列的重要更新版本，旨在为军事及关键任务通信系统中的无线电信号传输、调制解调、自动链路建立（ALE）、数据链路协议以及抗干扰性能提供统一的工程设计与验证准则。文档详细规定了在2至30MHz高频频段及邻近中频频段内，无线电设备应满足的电气性能、接口兼

展开>> 收起<<

MIL-STD-188-141D 中频和高频频段的无线电信号系统的设计准则 2017.pdf

共370页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

MIL-STD-188-141D 中频和高频频段的无线电信号系统的设计准则 2017

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: