MIL-PRF-24667D-2025 涂层系统，防滑，适用于滚涂或喷涂

VIP专免

那山那人那狗 2025-10-24 34 586.73KB 40 页 24星币

侵权投诉

Comments, suggestions, or questions on this document should be addressed to Commander, Naval Sea Systems

Command, ATTN: SEA 05S, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard, DC 20376-5160 or

emailed to CommandStandards@navy.mil, with the subject line “Document Comment”. Since contact information

can change, you may want to verify the currency of this address information using the ASSIST Online database at

https://assist.dla.mil.

AMSC N/A FSC 8010

Distribution Statement A. Approved for public release: distribution is unlimited.

INCH-POUND

MIL-PRF-24667D

w/AMENDMENT 1

11 AUGUST 2025

SUPERSEDING

MIL-PRF-24667D

16 February 2021

PERFORMANCE SPECIFICATION

COATING SYSTEM, NONSKID,

FOR ROLL OR SPRAY APPLICATION

This specification is approved for use by all Departments and Agencies of the Department of Defense.

1. SCOPE

1.1 Scope. This specification covers nonskid systems, coatings, and coverings for application to weather

decks, flight decks, and hangar decks of aircraft carriers, surface combatants, and amphibious, auxiliary, and sealift

ships, and submarines. Coatings are applied to steel, aluminum, and special hull treatment surfaces by spraying,

rolling, or other application method as designated by the manufacturer of the nonskid system.

1.2 Classification. The nonskid systems covered by this specification are of the following types, compositions,

classes, grades, and applications, as specified (see 6.2).

1.2.1 Types. The types of nonskid systems are as follows:

a. Type I - Standard durability, rollable

b. Type II - Standard durability, sprayable

c. Type III - Submerged applications, rollable

d. Type IV - Submerged applications, sprayable

e. Type V - Extended durability, rollable

f. Type VI - Extended durability, sprayable

1.2.2 Compositions. The compositions of nonskid systems are dependent on aggregate use and are categorized

as follows:

a. Composition D - Density-controlled abrasive deck system

b. Composition G - General use abrasive deck system

c. Composition L - Limited use aircraft carrier landing and run-out area deck system that is less abrasive to

the steel arresting cable

1.2.3 Classes. The classes of nonskid systems are segregated by functionality as follows:

a. Class 1 - Standard

b. Class 2 - Color stable

c. Class 3 - Low solar absorbent (LSA)

d. Class 4 - Resilient (for use where flexibility is required)

MIL-PRF-24667D

w/AMENDMENT 1

e. Class 5 - Submerged elastomeric applications

f. Class 6 - Low profile

g. Class 7 - High temperature

1.2.4 Grades. The grades of the nonskid system are based on the number of components in the coating:

a. Grade A - One component coating

b. Grade B - Two component coating

1.2.5 Application. The applications for nonskid systems are organized by cure characteristics as follows:

a. Application 1 - Standard cure

b. Application 2 - Fast cure

c. Application 3 - Low temperature cure

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This

section does not include documents cited in other sections of this specification or recommended for additional

information or as examples. While every effort has been made to ensure the completeness of this list, document

users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this

specification, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a

part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are

those cited in the solicitation or contract.

COMMERCIAL ITEM DESCRIPTIONS

A-A-59982 - Application Spray Equipment for Nonskid Coatings

A-A-59984 - Mixer, Automated, Transportable, Nonskid Coating

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-DTL-5624 - Turbine Fuel, Aviation, Grade JP-5 (NATO F-44)

MIL-D-16791 - Detergents, General Purpose (Liquid, Nonionic)

MIL-S-22698 - Steel Plate, Shapes and Bars, Weldable Ordinary Strength and Higher Strength:

Structural

MIL-PRF-23699 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Numbers:

O-152, O-154, O-156, and O-167

MIL-PRF-24385 - Fire Extinguishing Agent, Aqueous Film-Forming Foam (AFFF) Liquid

Concentrate, for Fresh and Sea Water

MIL-PRF-32177 - Cleaning Compound, Nonskid

MIL-PRF-83282 - Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO

Code Number H-537

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-1623 - Fire Performance Requirements and Approved Specifications for Interior Finish

Materials and Furnishings (Naval Shipboard Use)

(Copies of these documents are available online at https://quicksearch.dla.mil.)

MIL-PRF-24667D

w/AMENDMENT 1

2.2.2 Other Government documents, drawings, and publications. The following other Government documents,

drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified,

the issues of these documents are those cited in the solicitation or contract.

CODE OF FEDERAL REGULATIONS (CFR)

29 CFR 1910 - Occupational Safety and Health Standards

40 CFR 60, Appendix A-7,

Method 24

- Determination of Volatile Matter Content, Water Content, Density,

Volume Solids, and Weight Solids of Surface Coatings

40 CFR 63 - National Emission Standards for Hazardous Air Pollutants for Source

Categories

40 CFR 63, Subpart II - National Emission Standards for Shipbuilding and Ship Repair

(Surface Coating)

40 CFR 261.24 - Toxicity Characteristic

(Copies of these documents are available online at www.ecfr.gov.)

ENVIRONMENTAL PROTECTION AGENCY (EPA)

EPA SW-846 - Test Methods for Evaluating Solid Waste: Physical/Chemical Methods

(Copies of this document are available online at www.epa.gov.)

NATIONAL INSTITUTE FOR OCCUPATIONAL SAFETY AND HEALTH (NIOSH)

NIOSH Manual of Analytical Methods (NMAM),

Method 7500

- Silica, Crystalline, by XRD (Filter Redeposition)

(Copies of this document are available online at www.cdc.gov.)

NAVAL SEA SYSTEMS COMMAND (NAVSEA) PUBLICATIONS

T9070-AL-DPC-020/077-2 - NAVSEA Hazardous Material Avoidance Process

(Copies of this document are available from the applicable repositories listed in S0005-AE-PRO-010/EDM, which

can be obtained online via Model Based Product Support (MBPS) at

https://mbps.navseaplm.navy.mil/Windchill/app/. To gain access to MBPS, obtain an account with National Help

Desk Service Management (NHDSM) at https://nhdsm.navair.navy.mil (a valid CAC is required to access this

website) and submit a SAAR-N Request. Refer questions, inquiries, or problems to (888) 292-5919. Copies of this

document may also be obtained from the Naval Ships Engineering Drawing Repository (NSEDR) online at

https://199.208.213.105/webjedmics/index.jsp. To request an account for drawing access, send an email to

NNSY_JEDMICS_NSEDR_HELP_DESK@us.navy.mil.)

2.3 Non-Government publications. The following documents form a part of this document to the extent

specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or

contract.

ASTM INTERNATIONAL

ASTM A36/A36M - Standard Specification for Carbon Structural Steel

ASTM A229/A229M - Standard Specification for Steel Wire, Quenched and Tempered for

Mechanical Springs

ASTM A514/A514M - Standard Specification for High-Yield-Strength, Quenched and Tempered

Alloy Steel Plate, Suitable for Welding

ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #涂层

摘要：

MIL-PRF-24667D-2025 是一项美国军用性能规范，规定了用于舰船甲板、直升机起降平台及其他高流量区域的防滑涂层系统的最新要求，特别针对滚涂或喷涂施工工艺进行了优化。该标准旨在确保涂层在严苛的海洋环境中具备卓越的耐磨性、抗冲击性、耐化学腐蚀性以及长期防滑性能，同时适用于新造或维护翻新场景。通过明确滚涂与喷涂的操作参数、涂层厚度、固化时间及附着力测试方法，本规范帮助施工方避免因工艺不当导致的防滑失效或涂层剥落。对于采购方而言，遵循MIL-PRF-24667D可确保所选材料符合美国国防部

展开>> 收起<<

MIL-PRF-24667D-2025 涂层系统，防滑，适用于滚涂或喷涂.pdf

共40页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

MIL-PRF-24667D-2025 涂层系统，防滑，适用于滚涂或喷涂

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: