美国军用标准 MIL-DTL-55302G_AMENDMENT-2 铝合金装甲板详细规范

VIP专免

standardshare 2026-08-09 8 221.53KB 24 页 25星币

侵权投诉

AMSC N/A FSC 5935

INCH - POUND

MIL-DTL-55302G

w/AMENDMENT 2

16 November 2015

SUPERSEDING

MIL-DTL-55302G

w/AMENDMENT 1

23 January 2013

DETAIL SPECIFICATION

CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES

This specification is approved for use by all Departments and Agencies of the Department of Defense.

1. SCOPE

1.1 Scope. This specification covers connectors (plugs and receptacles) for printed circuit subassembly and their

accessories, for use with single-sided printed wiring, double-sided printed wiring, and multilayer printed wiring

conforming to IPC-2221 and MIL-PRF-31032, respectively (see 6.1). Contact termination types available (see 3.1)

are crimp, dip solder, flex, hand solder, and wire wrappost.

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This

section does not include documents cited in other sections of this specification or recommended for additional

information or as examples. While every effort has been made to ensure the completeness of this list, document

users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this

specification, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a

part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are

those cited in the solicitation or contract (see 6.2).

FEDERAL STANDARD

FED-STD-H28 - Screw-Thread Standards For Federal Services

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-DTL-14072 - Finishes for Ground Based Electronic Equipment

MIL-M-24519 - Molding Plastics, Electrical Thermoplastic

MIL-PRF-31032 - Printed Circuit Board/Printed Wiring Board, General Specification For

(See supplement 1 for list of specification sheets.)

Comments, suggestions, or questions on this document should be addressed to DLA Land and Maritime,

ATTN: VAI, 3990 East Broad Street, Columbus, OH 43218-3990 or email RectangularConnector@dla.mil. Since

contact information can change, you may want to verify the currency of this address information using the ASSIST

Online database at https://assist.dla.mil.

MIL-DTL-55302G

w/AMENDMENT 2

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-202 - Electronic and Electrical Component Parts

MIL-STD-810 - Environmental Engineering Considerations and Laboratory Tests

MIL-STD-889 - Dissimilar Metals

MIL-STD-1285 - Marking of Electrical and Electronic Parts

(Copies of these documents are available online at https://assist.dla.mil/quicksearch/ )

2.3 Non-Government publications. The following documents form a part of this document to the extent specified

herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see

6.2).

ASTM INTERNATIONAL

ASTM A240/A240M - Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for

Pressure Vessels for General Applications

ASTM A276 - Standard Specification for Stainless Steel Bars and Shapes

ASTM A342/A342M - Materials, Feebly Magnetic, Permeability Of

ASTM A480/A480M - Plate, Steel , Sheet and Strip, Flat-Rolled Stainless and Heat-Resisting

ASTM A484/A484M - Steel, Bars, Billets and Forgings, Stainless

ASTM A580/A580M - Standard Specification for Stainless Steel Wire

ASTM A581/A581M - Steel Wire and Wire Rods, Free Machining Stainless and Heat-Resisting

ASTM A582/A582M - Free-Machining Stainless and Heat-Resisting Steel Bars

ASTM B16/B16M - Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw

Machines

ASTM B36/B36M - Plate, Brass, Sheet, Strip, and Rolled Bar

ASTM B103/B103M - Plate, Phosphor Bronze, Sheet, Strip, and Rolled Bar

ASTM B121/B121M - Plate, Leaded Brass, Sheet, Strip, and Rolled Bar

ASTM B134/B134M - Standard Specification for Brass Wire

ASTM B139/B139M - Rod, Phosphor Bronze, Bar, and Shapes

ASTM B159/B159M - Phosphor Bronze Wire

ASTM B194 - Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B196/B196M - Rod and Bar, Copper-Beryllium Alloy

ASTM B197/B197M - Wire, Alloy Copper-Beryllium

ASTM B206/B206M - Copper-Nickel-Zinc Alloy (Nickel-Silver) Wire and Copper-Nickel Alloy Wire

ASTM B209 - Aluminum and Aluminum-Alloy Sheet and Plate, Standard Specification For

ASTM B301/B301M - Copper Rod, Bar, Wires, and Shapes, Free Cutting

ASTM B422 - Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy,

Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-

Nickel-Tin alloy Sheet and Strip, Standard Specification For

ASTM B441 - Copper Cobalt Beryllium (UNS NO. C17500) and Copper-Nickel-Beryllium (UNS NO.

C17510), Rod and Bar

ASTM B453/B453M - Copper Zinc Lead Alloy, (Lead Brass) Rod, Bar, and Shapes

ASTM B734 - Electrodeposited Copper for Engineering Uses, Standard Specification For

ASTM B740 - Copper Nickel Tin Spinodal Alloy Strip

ASTM B768 - Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Strip and Sheet,

Specification For

ASTM B888 - Copper Alloy Strip for Use in the Manufacture of Electrical Connectors or Spring

Contacts, Standard Specification For

ASTM D4067 - Material, Molding and Extrusion, Reinforced and Filled Polyphenylene Sulfide (PPS)

Injection

ASTM D5138 - Liquid Crystal Polymers (LCP), Standard Specification For

ASTM D5927 - Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test

Methods, Standard Specification For

ASTM D5948 - Compounds, Molding, Thermosetting

MIL-DTL-55302G

w/AMENDMENT 2

ASTM D6358 - Standard Classification System and Basis for Specification for Ply (Phenylene

Sulfide) (PPS) Injection Molding and Extrusion Materials Using ISO Methods

(Copies of these documents are available online at http://astm.org )

AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME)

ASME B46.1 - Surface Texture (Surface Roughness Waviness and Lay)

(Copies of these documents are available online at http://www.asme.org )

INTERNATIONAL ORGANIZATION FOR STANDARDS (ISO)

ISO 10012 – Measurement Management Systems – Requirements for Measurement Process and

Measuring Equipment

(Copies of these documents are available from www.ansi.org )

THE INSTITUTE FOR INTERCONNECTING AND PACKAGING ELECTRONIC CIRCUITS (IPC)

IPC-2221 - Printed Board Design, Generic Standard For

(Copies of these documents are available online from http://www.ipc.org )

ELECTRONIC COMPONENTS INDUSTRY ASSOCIATION (ECIA)

EIA-364 - Electrical Connector/Socket Test Procedures Including Environmental Classifications

EIA-364-06 - Contact Resistance Test Procedure for Electrical Connectors

EIA-364-08 - Crimp Tensile Strength Test Procedure for Electrical Connectors

EIA-364-20 - Withstanding Voltage Test Procedure for Electrical Connectors, Sockets and Coaxial

Contacts

EIA/ECA-364-21 - Insulation Resistance Test Procedure for Electrical Connectors, Sockets, and Coaxial

Contacts

EIA-364-23 - Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets

EIA/ECA-364-26 - Salt Spray Test Procedure for Electrical Connectors, Contacts and Sockets

EIA-364-27 - Mechanical Shock (Specified Pulse) Test Procedure for Electrical Connectors

EIA-364-28 - Vibration Test Procedure for Electrical Connectors and Sockets

EIA/ECA-364-29 - Contact Retention Test Procedure for Electrical Connectors

EIA-364-31 - Humidity Test Procedure for Electrical Connectors and Sockets

EIA-364-32 - Thermal Shock (Temperature Cycling) Test Procedure for Electrical Connectors and

Sockets

EIA-364-37 - Contact Engagement and Separation Force Test Procedure for Electrical Connectors

(Copies of these documents are available online at http://www.eciaonline.org)

NATIONAL CONFERENCE OF STANDARD LABRATORIES (NCSL)

NCSL Z540.3 - Requirements for the Calibration of Measuring and Test Equipment

(Copies of these documents are available online at http://www.ncsli.org)

NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)

NEMA-HP3 - Electrical and Electronic PTFE (Polytetrafluoro-ethylene Insulated High Temperature Hook-

up Wire, Types ET (250 Volts), E (600 Volts) and EE (1000 Volts)

(Copies of these documents are available online at http://www.nema.org)

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #铝合金 #合金 #甲板

摘要：

本页面提供美国军用标准MIL-DTL-55302G第2号修订版（AMENDMENT-2）的详细规范说明，该标准专门规定铝合金装甲板在军事应用中的材料性能、制造工艺、尺寸公差、力学性能及质量保证要求。作为美国国防部制定的重要军用规范，MIL-DTL-55302G涵盖铝装甲板的化学成分、热处理状态、抗弹道性能、焊接适应性及表面质量等关键技术指标，适用于坦克、装甲车辆、舰船及航空器防护结构的设计与制造。此修订版进一步优化了材料验收标准、测试方法及标记规则，确保铝合金装甲板在极端战场环境下具备可靠的防护

展开>> 收起<<

美国军用标准 MIL-DTL-55302G_AMENDMENT-2 铝合金装甲板详细规范.pdf

共24页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

美国军用标准 MIL-DTL-55302G_AMENDMENT-2 铝合金装甲板详细规范

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: