ASTM C1852 - 20 (2025) 气溶胶泡沫密封剂和粘合剂产品选择交付系统标准指南

VIP免费

标准小能手 2026-08-31 7 908.79KB 7 页 24星币

Designation: C1852 −20 (Reapproved 2025)
Standard Guide for
Product Selection/Delivery Systems for Aerosol Foam
Sealants and Adhesives
1
This standard is issued under the ﬁxed designation C1852; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide covers the general use of aerosol polyure-
thane and aerosol latex foams extruded from pressurized
containers intended for building envelope air barrier sealant
and adhesive applications in building construction. It also
provides an overview of associated standards and test methods
that quantify key physical properties that are useful to design
professionals, engineers, speciﬁers, and end users.
1.2 Currently two main foam sealant types are applicable to
this practice, single component polyurethane and latex types.
1.3 The values stated in inch-pound units are to be regarded
as standard. SI units provided are for information only and are
not considered standard.
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. For speciﬁc safety
considerations see Section 7.
1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
2
C168 Terminology Relating to Thermal Insulation
C557 Speciﬁcation for Adhesives for Fastening Gypsum
Wallboard to Wood Framing
C717 Terminology of Building Seals and Sealants
C1536 Test Method for Measuring the Yield for Aerosol
Foam Sealants
C1620 Speciﬁcation for Aerosol Polyurethane and Aerosol
Latex Foam Sealants
C1642 Practice for Determining Air Leakage Rates of Aero-
sol Foam Sealants and Other Construction Joint Fill and
Insulation Materials
C1643 Test Method to Measuring the Post Dispensing Volu-
metric Expansion of Aerosol Foam Sealants
C1737 Guide for Evaluating Temperature Effects to Aerosol
Foam Sealant During and After Dispensing
D883 Terminology Relating to Plastics
D3498 Speciﬁcation for Adhesives for Field-Gluing Wood
Structural Panels (Plywood or Oriented Strand Board) to
Wood Based Floor System Framing
D6464 Speciﬁcation for Expandable Foam Adhesives for
Fastening Gypsum Wallboard to Wood Framing
E72 Test Methods of Conducting Strength Tests of Panels
for Building Construction
E84 Test Method for Surface Burning Characteristics of
Building Materials
E119 Test Methods for Fire Tests of Building Construction
and Materials
E283 Test Method for Determining Rate of Air Leakage
Through Exterior Windows, Skylights, Curtain Walls, and
Doors Under Speciﬁed Pressure Differences Across the
Specimen
E814 Test Method for Fire Tests of Penetration Firestop
Systems
E2112 Practice for Installation of Exterior Windows, Doors
and Skylights
2.2 Other Standards:
AFG-01 Adhesives for Field-Gluing Plywood to Wood
Framing
3
UL 723 Test for Surface Burning Characteristics of Building
Materials
4
UL 1715 Fire Test of Interior Finish Material
4
1
This guide is under the jurisdiction of ASTM Committee C24 on Building Seals
and Sealants and is the direct responsibility of Subcommittee C24.61 on Aerosol
Foam Sealants.
Current edition approved Nov. 1, 2025. Published November 2025. Originally
approved in 2017. Last previous edition approved in 2020 as C1852-20. DOI:
10.1520/C1852-20R25.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at www.astm.org/contact. For Annual Book of
ASTM Standards volume information, refer to the standard’s Document Summary
page on the ASTM website.
3
Available from APA: www.https://www.apawood.org/.
4
Available from Underwriters Laboratories (UL), 2600 N.W. Lake Rd., Camas,
WA 98607-8542, http://www.ul.com.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1

AAMA 812 Voluntary Practice for Assessment of Single

Component Aerosol Expanding Polyurethane Foams for

Sealing Rough Openings of Fenestration Installations

NFPA 286: Standard Methods of Fire Tests for Evaluating

Contribution of Wall and Ceiling Interior Finish to Room

Fire Growth

Available from American Architectural Manufacturers Association (AAMA),

1827 Walden Office Square, Suite 550, Schaumburg, IL 60173-4268, http://

www.aamanet.org.

Available from National Fire Protection Association (NFPA), 1 Batterymarch

Park, Quincy, MA 02169-7471, http://www.nfpa.org.

Building Envelope Sealing Sealing: Gaps, Cracks & Joints Adhesive

Window, Door & Skylight Interior Perimeters Within Residential & Commercial Building Envelopes Structural Insulated Panels, Drywall, Subﬂoor & In-

sulated Concrete Forms

FIG. 1 Interior Window Perimeters of Exterior Wall Windows, Gaps/Holes (Fire Blocking), and Drywall Adhesive

FIG. 2 Interior Door Perimeters of Exterior Doors, Gaps/Holes (General), and Subﬂoor Adhesive

C1852 − 20 (2025)

3. Terminology

3.1 Deﬁnitions—For deﬁnitions of terms used in this guide,

refer to Terminologies C168,C717, and D883.

4. Summary of Guide

4.1 This guide is intended to provide general assistance for

a speciﬁer, engineer, design professional or end user who is

seeking material selection assistance for a one component

aerosol foam sealant. This guide provides an overview and

creates awareness of the most common uses of one component

foam sealants and further describes key product attributes and

performance criteria that may assist in the material selection

process. The guide explains only the most common uses of

polyurethane and latex foam sealants and provides an overview

FIG. 3 Skylight Perimeters, Joints, and Insulated Concrete Forms

FIG. 4 Commercial Window Interior Perimeters, Sealing Joints of Rigid Insulation, and Structural Insulated Panels (SIPs)

C1852 − 20 (2025)

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #气溶胶泡沫 #密封剂 #标准指南

摘要：

本页面向建筑材料、施工安装与密封保温领域的工程师、承包商及采购人员，全面解读ASTM C1852-20 (2025)标准指南，该指南针对气溶胶泡沫密封剂和粘合剂产品的选择与交付系统提供了系统化的技术规范要求。内容涵盖产品分类、性能评估、喷射速率、固化特性、储存稳定性、环境适应性及施工操作要点，帮助用户根据实际应用场景（如门窗安装、管道贯穿密封、建筑接缝填充等）精准匹配单组分泡沫或双组分泡沫，并合理选用带喷管、枪式或便携式分配设备。通过遵循该标准，可有效提升施工效率，减少材料浪费，确保密封与粘结质

展开>> 收起<<

ASTM C1852 - 20 (2025) 气溶胶泡沫密封剂和粘合剂产品选择交付系统标准指南.pdf

共7页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ASTM C1852 - 20 (2025) 气溶胶泡沫密封剂和粘合剂产品选择交付系统标准指南

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: