ISO IEC 11801-1-2017 cor1-2018

Carl 2024-09-12 11 373.57KB 7 页免费

侵权投诉

ISO/IEC 11801-1:2017/COR1:2018 – 1 –

ISO/IEC 11801-1

Edition 1.0 2017-11

INFORMATION TECHNOLOGY –

GENERIC CABLING FOR CUSTOMER PREMISES

Part 1: General requirements

CORRIGENDUM 1

Foreword

Replace, in list item d), “Category BCT-B, 8.1, and 8.2;” with “Categories BCT-B, 8.1 and

8.2;”.

Replace list item f) with the following new list item:

f) addition of cabled optical fibre Categories OS1a and OM5;

Replace, in list item g), “silica optical fibre cabling;” with “optical fibre classes;”

Replace list item h) with the following new list item:

h) cabled optical fibre Categories OM1, OM2 and OS1 have been moved to an informative

annex.

Introduction

Replace the first paragraph with the following new paragraph:

This document contains general requirements in support of the other premises-specific

referenced cabling design documents developed by ISO/IEC JTC 1/SC 25 including

ISO/IEC 11801-2, ISO/IEC 11801-3, ISO/IEC 11801-4, ISO/IEC 11801-5, ISO/IEC 11801-6,

related Technical Specifications and Technical Reports (including the ISO/IEC TR 11801-99xx

series, ISO/IEC TR 24704, ISO/IEC TR 24750 and ISO/IEC TS 29125).

ISO/IEC 11801-1:2017-11/COR1:2018-04(en)

– 2 – ISO/IEC 11801-1:2017/COR1:2018

Figure 1 – Relationships between the generic cabling documents produced by ISO/IEC

JTC 1/SC 25

Replace the figure graphic with the following new figure graphic:

3.1 Terms and definitions

In 3.1.26, delete “end-to-end” from the definition.

Delete the entire entry 3.1.32.

3.2 Abbreviations

Insert the following abbreviation:

connection

Replace:

FEXT far-end crosstalk attenuation (loss)

with:

FEXT far-end crosstalk (loss)

Replace:

NEXT near-end crosstalk attenuation (loss)

ISO/IEC 11801-1:2017/COR1:2018 – 3 –

with:

NEXT near-end crosstalk (loss)

3.3.1 Variables

Delete the following line:

connection

3.3.2 Indices

Delete the following line:

TO index to denominate a characteristic, measured from the TO

5.1 Functional elements

After the sentence “Groups of these functional elements are connected together to form

cabling subsystems.”, insert the following new note:

NOTE The numbering of the cabling subsystems does not imply a hierarchy.

Figure 5 – Equipment and test interfaces

Replace the figure graphic with the following new figure graphic:

Table 2 – Details of environmental classification

In row 20, insert “g/m

” after each numerical value in columns 2, 3 and 4, as follows:

– 4 – ISO/IEC 11801-1:2017/COR1:2018

Sodium chloride (salt/sea

water)

0 g/m3 < 0,3 g/m3 < 0,3 g/m3

In row 21, insert “mg/m3” after each numerical value in columns 2, 3 and 4, as follows:

Oil (dry-air concentration)

(for oil types see b)

0 mg/m3 < 0,005 mg/m3 < 0,5 mg/m3

In row 22, insert “mg/m3” after each numerical value in columns 3 and 4, as follows:

Sodium stearate (soap) None > 5 × 104 mg/m3 aqueous

non-gelling

> 5 × 104 mg/m3 aqueous

gelling

In rows 26 to 35, insert “mg/m3” after each numerical value in columns 2, 3 and 4, as follows:

Hydrogen sulphide < 0,003 mg/m3/

< 0,01 mg/m3

< 0,05 mg/m3/

< 0,5 mg/m3

< 10 mg/m3/ < 50 mg/m3

Sulphur dioxide < 0,01 mg/m3/

< 0,03 mg/m3

< 0,1 mg/m3/ < 0,3 mg/m3 < 5 mg/m3/ < 15 mg/m3

Sulphur trioxide (ffs) < 0,01 mg/m3/

< 0,03 mg/m3

< 0,1 mg/m3/ < 0,3 mg/m3 < 5 mg/m3/ < 15 mg/m3

Chlorine wet (> 50 %

humidity)

< 0,000 5 mg/m3/ < 0,001

mg/m3

< 0,005 mg/m3/

< 0,03 mg/m3

< 0,05 mg/m3/

< 0,3 mg/m3

Chlorine dry (< 50 %

humidity)

< 0,002 mg/m3/

< 0,01 mg/m3

< 0,02 mg/m3/

< 0,1 mg/m3

< 0,2 mg/m3/ < 1,0 mg/m3

Hydrogen chloride – / < 0,06 mg/m3 < 0,06 mg/m3/

< 0,3 mg/m3

< 0,6 mg/m3/ 3,0 mg/m3

Hydrogen fluoride < 0,001 mg/m3/

< 0,005 mg/m3

< 0,01 mg/m3/

< 0,05 mg/m3

< 0,1 mg/m3/ < 1,0 mg/m3

Ammonia < 1 mg/m3/ < 5 mg/m3 < 10 mg/m3/ < 50 mg/m3 < 50 mg/m3/ < 250 mg/m3

Oxides of nitrogen < 0,05 mg/m3/

< 0,1 mg/m3

< 0,5 mg/m3/ < 1 mg/m3 < 5 mg/m3/ < 10 mg/m3

Ozone < 0,002 g/m3/

< 0,005 g/m3

< 0,025 g/m3/ < 0,05 g/m3 < 0,1 g/m3/ < 1 g/m3

6.3.1 General

In the first sentence after list item 2), replace “two sub-Classes, L and M.” with

“two sub-Classes, L and M (see Table 5).”

6.3.3.2 Insertion loss/attenuation

In the last paragraph before Table 5, delete “, at maximum implementation,”.

6.3.3.6 Direct current loop resistance

Replace the first paragraph with the following new paragraph:

The DC loop resistance requirements are applicable to all cabling Classes.

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载

标签： #ISO

(ISO IEC 11801-1-2017 cor1-2018,（共7页）,pdf,373.57KB,https://www.bjxwk.com/doc/76365/)

展开>> 收起<<

ISO IEC 11801-1-2017 cor1-2018.pdf

共7页,预览4页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ISO IEC 11801-1-2017 cor1-2018

相关推荐

开通VIP享超值会员特权

相关内容

推荐作者

热门标签

举报选择: