BS 1490-1988_1998

VIP免费
逍遥书生 2024-09-15 16 465.78KB 30 页 12星币
侵权投诉
BRITISH STANDARD BS 1490:1988
Incorporating
Amendment
Nos.1&2
Specification for
Aluminium and
aluminium alloy ingots
and castings for general
engineering purposes
UDC 669.71– 412–14:621
Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Tue May 29 10:27:48 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
BS1490:1988
This British Standard, having
been prepared under the direction
of the Non-ferrous Metals
Standards Committee, was
published under the authority of
the Board of BSI and comes
intoeffect on
30 June 1988
© BSI 12-1998
First published, August 1949
First revision October 1955
Second revision May 1963
Third revision December 1970
Fourth revision June 1988
The following BSI references
relate to the work on this
standard:
Committee reference NFM/35
Draft for comment 86/39422 DC
ISBN 0 580 16575 2
Committees responsible for this
British Standard
The preparation of this British Standard was entrusted by the Non-ferrous
Metals Standards Committee (NFM/-) to Technical Committee NFM/35, upon
which the following bodies were represented:
Aluminium Federation
Aluminium Stockholders’ Association
Association of Light Alloy Refiners Limited
Department of Trade and Industry (Minerals and Metals Division)
Light Metal Founders’ Association
Magnesium Industry Council
Royal Institute of British Architects
Society of Motor Manufacturers and Traders Limited
The following bodies were also represented in the drafting of the standard,
through subcommittees and panels:
BNF Metals Technology Centre
British Foundry Association
British investment Casting Trade Association
Institute of British Foundrymen
Amendments issued since publication
Amd. No. Date of issue Comments
6309 March 1990
6605 December 1990 Indicated by a sideline in the margin
Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Tue May 29 10:27:48 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
BS1490:1988
© BSI 12-1998 i
Contents
Page
Committees responsible Inside front cover
Foreword ii
1 Scope 1
2 Definitions 1
3 General requirements 2
4 Specific requirements for ingots 2
5 Specific requirements for castings 6
6 Inspection procedures 6
7 Test samples 8
8 Test methods 9
Appendix A Information to be supplied by the purchaser 15
Appendix B Recommendations for optional supplementary
inspection and tests for castings 15
Appendix C Colour code for ingots 18
Appendix D Guide to the selection of alloys 18
Figure 1 — Sand or chill cast test samples: forms A and B 9
Figure 2 — Chill cast test samples: forms C and D 10
Figure 3 — Sand cast test sample: form E 11
Figure 4 — Sand cast test sample: form F 12
Figure 5 — Investment cast test sample: form G (“cast to size”) 13
Figure 6 — Investment cast test sample: form H 14
Table 1 — Chemical compositions of group A ingots and castings:
general purpose alloys 3
Table 2 — Chemical compositions of group B ingots and castings:
special purpose alloys 4
Table 3 — Chemical compositions of group C ingots and castings:
special purpose alloys of limited application 5
Table 4 — Mechanical properties for castings (obtained on
separately cast test samples) 7
Table 5 — Hardness of castings 8
Table 6 — Colour code for ingots 18
Table 7 — Machinability ratings of aluminium casting alloys 21
Table 8 — Comparison of casting characteristics and other properties 24
Publications referred to Inside back cover
Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Tue May 29 10:27:48 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
摘要:

BS 1490-1988_1998 是英国标准学会发布的关于铝及铝合金铸件与铸锭的标准规范,该标准涵盖了通用工程用铝合金铸件与铸锭的化学成分、力学性能、取样方法及验收条件。该标准在1988年首次发布,并于1998年进行了修订与重新确认,因此常被引用为 BS 1490-1988 (1998)。它适用于砂型铸造、金属型铸造及压力铸造等多种铸造工艺,为铝合金铸件的质量控制和采购验收提供了权威依据。该标准的技术内容部分被后续的 BS EN 1706 等欧洲标准取代,但在许多老式设计文件、出口合同及对照历

展开>> 收起<<
BS 1490-1988_1998.pdf

共30页,预览4页

还剩页未读, 继续阅读

声明:本文档系会员上传,若文档所含内容侵犯了您的版权或隐私,请立即通知,我们立即给予侵权申诉删除!
作者:逍遥书生 分类:国际标准 价格:12星币 属性:30 页 大小:465.78KB 格式:PDF 时间:2024-09-15

开通VIP享超值会员特权

  • 多端同步记录
  • 高速下载文档
  • 免费文档工具
  • 分享文档赚钱
  • 每日登录抽奖
  • 优质衍生服务
/ 30
客服
关注