SAE AMS 4710H-2018

VIP免费
Carl 2024-11-15 8 1.09MB 5 页 20星币
侵权投诉
__________________________________________________________________________________________________________________________________________
SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely
voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”
SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and
suggestions.
Copyright © 2018 SAE International
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SAE.
TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)
Tel: +1 724-776-4970 (outside USA)
Fax: 724-776-0790
Email: CustomerService@sae.org
SAE WEB ADDRESS: http://www.sae.org
SAE values your input. To provide feedback on this
Technical Report, please visit
http://standards.sae.org/AMS4710H
AEROSPACE
MATERIAL SPECIFICATION
AMS4710™
REV. H
Issued 1942-12
Noncurrent 1977-03
Revised 2007-07
Reaffirmed 2012-09
Stabilized 2018-01
Superseding AMS4710G
Brass Wire, Tinned
65Cu - 35Zn
Annealed (061)
(Composition similar to UNS C27000)
RATIONALE
AMS4710H stabilizes this document because it is no longer state of the art and other documents contain similar but not
necessarily equivalent requirements.
STABILIZED NOTICE
AMS4710H has been declared "STABILIZED" by SAE AMS Committee D Nonferrous Alloys. This document was stabilized
because this document contains mature technology that is not expected to change and thus no further revisions are
anticipated. Previously this document was reaffirmed. The last technical update of this document occurred in July, 2007.
Users of this document should refer to the cognizant engineering organization for disposition of any issues with
reports/certifications to this specification; including exceptions listed on the certification.
NOTE: In many cases, the purchaser may represent a sub tier supplier and not the cognizant engineering organization.
AMS Committee D recommends that the following similar but not identical specifications be used for the “STABILIZED”
specification.
ASTM B134 Brass Wire
Downloaded from SAE International by Univ of Toronto, Tuesday, January 04, 2022
SAE INTERNATIONAL
AMS4710™H
Page 1 of 4
_________________________________________________________________________________________________
Downloaded from SAE International by Univ of Toronto, Tuesday, January 04, 2022
SAE INTERNATIONAL
AMS4710™H
Page 2 of 4
_________________________________________________________________________________________________
Downloaded from SAE International by Univ of Toronto, Tuesday, January 04, 2022

标签： #MS

摘要：

SAE AMS 4710H-2018 是美国汽车工程师学会发布的军标级黄铜棒与型材技术规范，专门针对含铜59.0%-63.0%、铅1.5%-2.5%的易切削黄铜合金制定。该标准替代了之前的AMS 4710G版本，主要修订了化学成分的检测方法、力学性能指标以及交货状态的验收要求。它适用于航空航天、军工装备及精密仪器中需高强度、良好切削加工性及耐腐蚀性的结构件与连接件。本规范严格规定了热加工或冷加工后的拉伸强度（最低331 MPa）、屈服强度及伸长率，同时明确了晶粒度、应力腐蚀开裂敏感性等关键质量参

展开>> 收起<<
SAE AMS 4710H-2018.pdf

共5页,预览4页

还剩页未读， 继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

相关推荐

更多
立即下载
作者：Carl 分类：国外协会 价格：20星币 属性：5 页 大小：1.09MB 格式：PDF 时间：2024-11-15

开通VIP享超值会员特权

  • 多端同步记录
  • 高速下载文档
  • 免费文档工具
  • 分享文档赚钱
  • 每日登录抽奖
  • 优质衍生服务

相关内容

更多

热门标签

ISO 混凝土 技术规范 检验 航空航天 不锈钢 消防 压力容器 铝合金 法兰
/ 5
评分 收藏
分享
立即下载 VIP免费下载
客服
关注