JIS C7551-1-2009

VIP免费
老杨树 2024-12-17 8 1.59MB 51 页 14星币
侵权投诉
JIS C 7551-1
:2009
(JELMA/JSA)
JAPANESE
INDUSTRIAL
STANDARD
Translated and Published
by
Japanese
Standards Association
Incandescent
lamps
-Safety
specifications -
Part
1:
Tungsten
filament
lamps
for domestic
and
similar general lighting purposes
ICS
29.140.20
Reference
number:
JIS
C 7551-1 :
2009
(E)
PROTECTED
BY
COPYRIGHT 26 S
C 7551-1 :
2009
Date
of
Establishment:
1999-03-20
Date
of
Revision: 2009-06-20
Date
of
Public
Notice
in
Official
Gazette:
2009-06-22
Investigated
by:
Japanese
Industrial
Standards
Committee
Standards
Board
© JSA 2010
Technical
Committee
on
Electricity
Technology
JIS C 7551-1 : 2009, First
English
edition
published
in
2010-08
Translated
and
published
by:
Japanese
Standards
Association
4-1-24,
Akasaka,
Minato-ku,
Tokyo, 107-8440
JAPAN
In
the
event
of
any
doubts
arising
as
to
the
contents,
the
original
JIS is
to
be
the
final
authority.
All
rights
reserved.
Unless
otherwise
specified,
no
part
of
this
publication
may
be
reproduced
or
utilized
in
any
form
or
by
any
means,
electronic
or
mechanical,
including
photocopying
and
microfilm,
without
permission
in
writing
from
the
publisher.
Printed
in
Japan
KK/HN
PROTECTED
BY
COPYRIGHT
C 7551-1 :
2009
Contents
Page
Introduction······························································································
·1
1
Scope································································································1
2
Normative
references···········································································
2
3
Terms
and
definitions··········································································
3
4
General
safety
requirements
.................................................................
4
4.1
General·····························································································
4
4.2
Marking·
.........................................................................................
··4
4.3
Protection
against
accidental
contact
in
screw
lamp
holders
························5
4.4
Lamp
cap
temperature
rise
...................................................................
5
4.5
Resistance
to
torque············································································
7
4.6
Insulation
resistance
of
bayonet
capped
lamps
(B
type)
and
other
lamps
having
insulated
skirts········································································
8
4.7
Metal
parts
intended
to
be
insulated
from
live
parts
and
height
of
side
solder·······························································································
8
4.8
Creepage
distances
for
B15d
and
B22d
capped
lamps
................................
9
4.9
Safety
at
end
of
life·············································································
9
4.10
Interchangeability'"
...........................................................................
9
4.11
Information
for
luminaire
design
..........................................................
10
5
Test································································································
·10
5.1
Type
test
(design
test,
periodic
test)
......................................................
10
5.2
Lot
test
(production
test)
....................................................................
·11
5.3
Test
procedures················································································
·11
Annex
A
(normative)
Miscellaneous
test
procedures
.....................................
·12
Annex
B
(normative)
Packaging
marking
symbols
(pictograms)························
·13
Annex
C
(normative)
Resistance
to
torque
test
procedures······························
·15
Annex
D
(normative)
Induced-failure
test····················································
·18
Annex
E
(normative)
Operation-to-failure
test
procedures·······························
·22
Annex
F
(normative)
..................................................................................
·24
Annex
G
(normative)
..................................................................................
·24
Annex
H
(normative)
..................................................................................
·24
Annex
J
(normative)
Method
of
measuring
mains
impedance···························
·25
Annex
K
(informative)
Information
for
luminaire
design·································
·27
(i)
PROTECTED
BY COPYRIGHT
摘要：

JIS C7551-1-2009 是日本工业标准中针对灯头和灯座安全性及互换性要求的重要技术规范，该标准等同于国际电工委员会（IEC）的对应标准，主要规定了各类电光源用灯头的尺寸、机械强度、电气性能以及耐热性等关键指标，适用于家用及类似普通照明设备的灯头设计与检测。通过明确标准化要求，该规范旨在确保不同制造商生产的灯头与灯座之间的兼容性，防止因尺寸偏差或材料缺陷导致的接触不良、过热或电气短路风险。无论是灯具设计人员、质量检验工程师还是进出口贸易商，在涉及日本市场的照明产品时，均需依据JIS C7

展开>> 收起<<
JIS C7551-1-2009.pdf

共51页,预览4页

还剩页未读， 继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

相关推荐

更多
立即下载
作者：老杨树 分类：国际标准 价格：14星币 属性：51 页 大小：1.59MB 格式：PDF 时间：2024-12-17

开通VIP享超值会员特权

  • 多端同步记录
  • 高速下载文档
  • 免费文档工具
  • 分享文档赚钱
  • 每日登录抽奖
  • 优质衍生服务

相关内容

更多

热门标签

ISO 混凝土 技术规范 检验 航空航天 不锈钢 消防 压力容器 铝合金 法兰
/ 51
评分 收藏
分享
立即下载 VIP免费下载
客服
关注