ASTM A824 - 01 (2022)

VIP免费

Carl 2024-09-02 9 57.78KB 3 页 10星币

Designation: A824 −01 (Reapproved 2022)
Standard Speciﬁcation for
Metallic-Coated Steel Marcelled Tension Wire for Use With
Chain Link Fence
1
This standard is issued under the ﬁxed designation A824; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This speciﬁcation covers 0.177 in. (4.50 mm) diameter
metallic-coated carbon steel marcelled tension wire for use
with chain-link fence. The 0.177 in. (4.50 mm) diameter
metallic-coated wire shall be produced in accordance with
Speciﬁcation A817. Three types of coatings are covered:
1.1.1 Type I—Aluminum-coated (aluminized),
1.1.2 Type II—Zinc-coated (galvanized), and
1.1.3 Type III—Zinc-5 % Aluminum Mischmetal (Zn5Al-
MM) alloy-coated.
1.2 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
information only.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
2
A700 Guide for Packaging, Marking, and Loading Methods
for Steel Products for Shipment
A817 Speciﬁcation for Metallic-Coated Steel Wire for
Chain-Link Fence Fabric and Marcelled Tension Wire
A902 Terminology Relating to Metallic Coated Steel Prod-
ucts
3. Terminology
3.1 Deﬁnitions:
3.1.1 For deﬁnitions of terms used in this speciﬁcation, refer
to Terminology A902.
3.2 Deﬁnitions of Terms Speciﬁc to This Standard:
3.2.1 marcelling—a process whereby either a uniform helix
or a series of waves is put in a wire to facilitate tensioning the
wire when installed to support the top or bottom, or both, of the
chain-link fabric (see 5.2.1).
4. Ordering Information
4.1 Orders for metallic-coated steel tension wire should
include the following information:
4.1.1 Quantity (expressed in number of coils),
4.1.2 Name of product,
4.1.3 Type of coating (see 5.3),
4.1.4 Class of coating if applicable (see 5.3.2 and 5.3.3),
4.1.5 Packaging requirements (see Section 14),
4.1.6 Certiﬁcation or test report, or both, if speciﬁed (see
Section 13), and
4.1.7 ASTM designation and year of issue.
NOTE 1—A typical ordering description is as follows: 20 coils metallic-
coated steel tension wire, Type II, Class 2, in 100-lb coils, to ASTM
A824 – ___ .
5. Materials and Manufacture
5.1 The steel rod from which the wire is drawn shall be
manufactured by the open-hearth, electric-furnace, or basic-
oxygen process.
5.2 The 0.177 in. (4.50 mm) diameter wire shall be cold-
drawn, metallic-coated at ﬁnished size to produce the speciﬁed
mechanical properties per Speciﬁcation A817, then marcelled
as speciﬁed in 5.2.1.
5.2.1 Marcelling shall produce a helix or series of waves in
the wire with the offset distance from the wire axis to the wave
peaks or the helix not less than 0.125 in. (3.18 mm) (measured
to the center of the wire). The pitch (distance between
successive points on the waves or helix) shall be not more than
12 in. (305 mm). Prior to making measurements of the
marcelling, curvature from coiling shall be removed by the
application of a 500-lbf (2225-N) tensile load. Maintain the
1
This speciﬁcation is under the jurisdiction of ASTM Committee F14 on Fences
and is the direct responsibility of Subcommittee F14.40 on Chain Link Fence and
Wire Accessories.
Current edition approved Nov. 1, 2022. Published November 2022. Originally
approved in 1984. Last previous edition approved in 2017 as A824 – 01(2017).
DOI: 10.1520/A0824-01R22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1

load while measuring the offset distance and pitch. Measure-
ments shall be made on a section of wire with a length at least
two times the pitch length.
5.2.1.1 Measurement of offset distance may be performed
by placing a straightedge against two adjacent peaks or
corresponding points on a helix, measuring the distance to the
inside of the wire 180° opposite, and dividing the value by two.
5.3 The 0.177 in. (4.50 mm) diameter wire shall be fur-
nished with one of three types of coating, per Speciﬁcation
A817 as speciﬁed:
5.3.1 Type I—Aluminum-Coated (Aluminized), with coating
weight speciﬁed.
5.3.2 Type II—Zinc-Coated (Galvanized), in three classes of
coating weights as speciﬁed.
5.3.3 Type III—Zinc-5 % Aluminum-Mischmetal Alloy
Coated (Zn-5Al-MM), in two classes of coating weights as
speciﬁed.
6. Mechanical Properties
6.1 The breaking strength shall meet the requirement of
Speciﬁcation A817 for 0.177 in. (4.50 mm) diameter wire.
7. Size and Tolerance
7.1 The diameter shall meet the requirements of Speciﬁca-
tion A817 for 0.177 in. (4.50 mm) diameter wire.
NOTE 2—It is recognized that the surfaces of heavy metallic coatings,
particularly those produced by the hot-dip process, are not perfectly
smooth. If the tolerance speciﬁed is rigidly applied to such irregularities
that are inherent to the product, unjustiﬁed rejections of wire that would
actually be satisfactory for use would occur. Therefore, it is intended that
this tolerance be used in gaging the uniform areas of the coated wire.
8. Weight of Coating
8.1 The weight of coating shall meet the requirements of
Speciﬁcation A817 for the Type and Class of coating speciﬁed.
9. Adherence of Coating
9.1 The adherence of coating shall meet the requirements of
Speciﬁcation A817 for 0.177 in. (4.50 mm) wire.
10. Number of Tests and Retests
10.1 A lot shall consist of all of the coils of wire of the same
size, type, and class, and shall be offered for inspection at one
time. A wire sample of sufficient length, approximately 4 ft (1.2
m), shall be cut from either end of each coil selected for tests
described in Sections 6,8, and 9.
10.2 The number of test specimens taken from the ends of
coils during production to ensure compliance with Sections 6
and 7varies with the quality control procedures and the
manufacturing facilities of each manufacturer, but is generally
not less than 10 % of the coils produced. For the purpose of
ﬁnal product testing, one specimen from every ten coils or
fraction thereof in a lot shall be selected at random, or a total
of seven specimens, whichever is less.
10.3 Should one or more of the wire specimens fail any
requirement, the lot shall be subjected to retest. For retest
purposes the original lot shall be regrouped into 50 coil lots or
fractions thereof. Each lot shall be tested for the property in
which the original sample failed to comply at a frequency of
10 % or more so that the total number of tests is at least double
the original. Any lot that exhibits a failure shall be rejected. If
during retesting an additional quality parameter is observed to
be defective, the lot of 50 is subject to rejection for that cause.
The manufacturer may test each coil in the failed lot for the
property in which failure occurred and reject only the noncon-
forming coils.
10.4 If any test specimen shows the presence of a weld or an
obvious defect, it may be discarded and another specimen
substituted.
10.5 Test specimens shall also be tested for compliance with
marcelling dimensions (see 5.2.1). For this purpose, the
test specimen shall contain at least three peaks and three
valleys.
11. Inspection
11.1 Unless otherwise speciﬁed in the contract or purchase
order, the producer is responsible for the performance of all
inspection and test requirements of this speciﬁcation. Except as
otherwise speciﬁed in the contract or purchase order, the
producer may use his own or any other suitable facilities for the
performance of the inspection and test requirements unless
disapproved by the purchaser at the time the order is placed.
The purchaser shall have the right to perform any of the
inspections and tests prescribed in this speciﬁcation when such
inspections and tests are deemed necessary to ensure that the
material conforms to prescribed requirements.
12. Rejection and Rehearing
12.1 Material that fails to conform to the requirements of
this speciﬁcation may be rejected. Rejections should be re-
ported to the producer or supplier promptly and in writing. In
case of dissatisfaction with the results of the test, the producer
or supplier may make claim for a rehearing.
12.2 The material must be adequately protected and cor-
rectly identiﬁed in order that the producer or supplier may
make a proper investigation.
13. Certiﬁcation
13.1 When speciﬁed in the purchase order or contract, a
producer’s or supplier’s certiﬁcation shall be furnished to the
purchaser that the material was manufactured, sampled, tested,
and inspected in accordance with this speciﬁcation and has
been found to meet the requirements. When speciﬁed in the
contract or purchase order, a report of the test results shall be
furnished.
14. Packaging, Package Marking, and Loading
14.1 Marking shall be by a tag securely attached to each coil
of tension wire and shall show the identity of the producer,
quantity, type of coating, class of coating (if applicable), and
ASTM designation.
14.2 Packaging of the coils of wire shall be agreed upon
between the producer and the purchaser. This agreement may
include coil dimensions and weight.
A824 − 01 (2022)
2

14.3 Unless otherwise speciﬁed, the packaging, package

marking, and loading shall be in accordance with Practices

A700.

15. Keywords

15.1 chain link fence; marcelled wire; metallic coated steel

wire; steel wire; wire

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned

in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk

of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ﬁve years and

if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards

and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the

responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should

make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,

United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above

address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website

(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222

Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/

A824 − 01 (2022)

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

已全部加载

摘要：

ASTM A824 - 01 (2022) 是由美国材料与试验协会发布的一项关于特定类型钢管的标准化规范，主要涵盖用于高压或特殊工况下的无缝与焊接钢管的化学成分、力学性能、尺寸公差及检验要求。该标准于2001年首次发布，并于2022年进行了最新确认，以确保其技术条款仍符合当前工业应用需求。内容详细规定了材料的抗拉强度、屈服强度、延伸率等关键指标，并对表面质量、无损检测及标记方式提出了明确要求。适用于石油、化工、能源及结构工程等领域中需要高可靠性和耐久性的管道系统。工程师、质量检验人员及采购方均可

展开>> 收起<<

ASTM A824 - 01 (2022).pdf

共3页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ASTM A824 - 01 (2022)

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: