ASTM A1067 - A 1067M - 12a (2018)

VIP免费

Carl 2024-09-02 11 346.1KB 8 页 14星币

Designation: A1067/A1067M −12a (Reapproved 2018)

Standard Speciﬁcation for

Test Coupons for Steel Castings

This standard is issued under the ﬁxed designation A1067/A1067M; the number immediately following the designation indicates the

year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last

reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.

1. Scope*

1.1 This speciﬁcation deﬁnes the geometries of several

separately cast and integrally cast test coupons for use as

speciﬁed in the applicable casting product or common require-

ments standard. This standard does not address procedures for

molding, casting, heat treating, machining, or testing; these

items are addressed as needed and appropriate by the appli-

cable product or common requirements standard.

NOTE 1—The test coupons described herein were formerly deﬁned in

multiple casting speciﬁcations. Those standards now reference this docu-

ment when test coupons are required and should be consulted for

applicable manufacturing and processing requirements.

1.2 Units—The values stated in either SI units or inch-

pound units are to be regarded separately as standard. The

values stated in each system may not be exact equivalents;

therefore, each system shall be used independently of the other.

Combining values from the two systems may result in noncon-

formance with the standard.

1.3 This standard does not purport to address all of the

safety concerns, if any, associated with its use. It is the

responsibility of the user of this standard to establish appro-

priate safety, health, and environmental practices and deter-

mine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accor-

dance with internationally recognized principles on standard-

ization established in the Decision on Principles for the

Development of International Standards, Guides and Recom-

mendations issued by the World Trade Organization Technical

Barriers to Trade (TBT) Committee.

2. Ordering Information

2.1 The applicable casting product standard or common

requirements standard, or both, provide information regarding

the number of coupons, molding materials to be used, heat

treatment concerns, and other processing issues.

3. Materials and Manufacture

3.1 Unless otherwise speciﬁed by the purchaser, test cou-

pons shall be poured from the same heat, or from the same

master heat, or from a sub-heat from the same master heat as

the castings they are to represent.

3.2 Except where speciﬁed herein or in the applicable

product or common requirements standard, the details of the

gating and risering of the coupons are left to the discretion of

the producer.

3.3 The test coupons shall be processed and heat treated as

speciﬁed in the applicable product or common requirements

speciﬁcation. Except when speciﬁed otherwise, the portion of

the test coupon from which the test specimen or specimens are

to be machined may be cut from the riser or feeder prior to heat

treatment.

4. Performance Requirements

4.1 The primary function of the test coupon is to provide

sound specimens useable for the determination of mechanical,

physical, corrosion, or other properties of the metal used to

produce the castings. If the test results conform to the stated

requirements, then the test coupon may be considered to have

functioned acceptably.

5. Other Requirements

5.1 The casting producer shall establish procedures for the

identiﬁcation and traceability of the coupons from pouring

through testing.

6. Dimensions and Permissible Variations

6.1 The drawings shown in this standard are not necessarily

drawn to scale. The values shown in the tables constitute the

dimensional requirements.

6.2 The drawings shown in this standard depict the more

commonly used test coupons (Figs. 1-9). Other designs may be

suitable when shown to produce acceptable properties or where

agreed.

7. Workmanship, Finish, and Appearance

7.1 Care should be taken in the preparation and pouring of

the molds to avoid the creation of inclusions or other anomalies

in the resulting test specimens.

This speciﬁcation is under the jurisdiction of ASTM Committee A01 on Steel,

Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee

A01.18 on Castings.

Current edition approved March 1, 2018. Published March 2018. Originally

approved in 2010. Last previous edition approved in 2012 as A1067/A1067M – 12a.

DOI: 10.1520/A1067_A1067M-12AR18.

*A Summary of Changes section appears at the end of this standard

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the

Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

8. Sampling

8.1 Care shall be taken in the production and processing of

the test coupon to ensure that it is representative of the casting

or castings it represents.

9. Number of Tests and Retests

9.1 Sufficient test coupons shall be produced to provide the

needed number of test specimens.

10. Certiﬁcation

10.1 Certiﬁcation of the test coupon is not applicable,

except when speciﬁed by the casting purchaser.

11. Product Marking

11.1 Marking of test coupons other than as necessary to

provide the identiﬁcation and traceability described in 6.1 is

not needed, except where speciﬁed by the casting purchaser

and agreed by the producer.

12. Keywords

12.1 castings; heat; master heat; stainless steel; steel; sub-

heat; test bar; test coupon

Feature 4-leg design 2-leg design

in. mm in. mm

⁄

60 2

⁄

35 1

⁄

C250250

⁄

35 1

⁄

E Optional Optional Optional Optional

⁄

215 3

⁄

100

T****

L 5 min. 125 min. 5 min. 125 min.

⁄

12.5

⁄

12.5

Rx 0 –

⁄

0–2 0–

⁄

0–2

*Use of and size of taper is at the discretion of the foundry.

FIG. 1 Test Coupons for Castings

A1067/A1067M − 12a (2018)

Feature in. mm

⁄

B 5 to 11 125 to 280

C 4 100

⁄

to 3

⁄

13 to 90

E 5 125

⁄

105

G3 75

⁄

FIG. 2 Test Coupon for Tension Test

Feature in. mm

⁄

B 3 min.* 80 min.*

C 1.00 25

⁄

** 5**

⁄

** 5**

ØE

⁄

* 13*

*Suggested Dimension **Plus ﬁnishing stock

FIG. 3 Design and Dimensions of the ICI Test Coupon

A1067/A1067M − 12a (2018)

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

摘要：

ASTM A1067 - A 1067M - 12a (2018) 是美国材料与试验协会（ASTM）发布的一项关于碳钢与合金钢无缝及焊接管道用耐高温钢锻件与管件的标准规范。该标准于2018年重新批准，涵盖了材料化学成分、力学性能、热处理要求及检验方法，适用于石油、化工、电力等高温高压工业领域。其内容旨在确保管件与锻件在高温环境下的强度、韧性和抗腐蚀性能，为工程设计、质量控制和采购验收提供统一技术依据。遵循该标准可提升管道系统的安全性与长期可靠性，是国际工程中广泛引用的重要参考文件。

展开>> 收起<<

ASTM A1067 - A 1067M - 12a (2018).pdf

共8页,预览4页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ASTM A1067 - A 1067M - 12a (2018)

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: