MIL-DTL-32082A

VIP专免

standardshare 2025-06-14 7 213.8KB 16 页 14星币

侵权投诉

Comments, suggestions, or questions on this document should be addressed to: Attn: DLA

Troop Support Standardization Team, 700 Robbins Avenue, Philadelphia, PA 19111-5096.

Since contact information can change, you may want to verify the currency of the address

information using Acquisition Streamlining and Standardization Information System

(ASSIST) online database https://assist.daps.dla.mil/

AMSC N/A FSC 8415

INCH-POUND

MIL-DTL-32082A

16 February 2012

SUPERSEDING

MIL-DTL-32082

1 May 2001

DETAILED SPECIFICATION

COVERALLS, MECHANICS, COLD WEATHER

This specification is approved for use by all Department and Agencies of the Department of

Defense (DoD).

1. SCOPE

1.1 Scope. This specification covers requirement for a coverall made from camouflage

printed cotton/nylon twill cloth intended to be worn by mechanics in the Department of the

Army as a protective garment over cold weather clothing.

1.2 Classification. (see 6.2).

1.2.1 Types. The coverall types are as follows:

Type I - Woodland Camouflage Print

Type II - Desert Camouflage Print

Type III - Universal Camouflage Print

1.2.2 Sizes. The coverall sizes are as follows:

Small, Medium, Large, X Large, and XX Large.

Note: The above mentioned sizes may be abbreviated as:

SML, MED, Large, XLG, and XXLG.

Provided by IHS

Licensed by www.sepana.ir

Sale only by www.sepana.ir, 05/22/2014 00:28:24 MDT

No reproduction or networking permitted without license from IHS

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com

MIL-DTL-32082A

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in Sections 3, 4, or 5 of this

specification. This section does not include documents cited in other sections of this

specification or recommended for additional information or as examples. While every effort has

been made to ensure the completeness of this list, document users are cautioned that they must

meet all specified requirements of documents cited in Sections 3, 4, or 5 of this specification

whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and

handbooks form a part of this document to the extent specified herein. Unless otherwise

specified, the issues of these documents are those cited in the solicitation or contract (see 6.2).

COMMERCIAL ITEM DESCRIPTIONS

A-A-55634 - Zippers (Fasteners, Slide Interlocking)

A-A-55126 - Fastener Tape, Hook and Loop, Synthetic

A-A-50199 - Thread, Polyester Core, Cotton, or Polyester Covered

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-DTL-44031 - Cloth, Camouflage Pattern, Cotton and Nylon

MIL-C-44034 - Cloth, Twill, Camouflage pattern, Cotton and Nylon for Desert Uniform

MIL-W-5664 - Webbing, Textile, Elastic

(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or

from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D,

Philadelphia, PA 19111-5094.)

2.3 Non-Government publications. The following documents form a part of this document

to the extent specified herein. Unless otherwise specified, the issues of these documents are

those cited in the solicitation or contract (see 6.2).

AMERICAN ASSOCIATION OF TEXTILE CHEMIST AND COLORISTS (AATCC)

AATCC Test Method 88B - Smoothness of Seams in Fabrics after Repeated Home

Laundering

(Copies of documents are available on line at www.aatcc.org or from the American Association

of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709-2215.)

AMERICAN SOCIETY FOR QUALITY (ASQ)

Provided by IHS

Licensed by www.sepana.ir

Sale only by www.sepana.ir, 05/22/2014 00:28:24 MDT

No reproduction or networking permitted without license from IHS

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com

MIL-DTL-32082A

ANSI/ASQ Z1.4 - Sampling Procedures and Tables for Inspection by Attributes

(Copies are available online at http://www.asq.org or from the American Society for Quality, 600

North Plankinton Avenue, Milwaukee, WI 53203.)

ASTM INTERNATIONAL

ASTM D 6193 - Standard Practice for Stitches and Seams

ASTM D 5035 - Standard Test Method for Breaking Force and Elongation of Textile Fabrics

(Strip Method)

(Copies of documents are available online at http://www.astm.org or from the ASTM

INTERNATIONAL, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-

2959.)

2.4 Order of precedence. Unless otherwise noted herein or in the contract in the event of a

conflict between the text of this document and the references cited herein, the text of this

document takes precedence. Nothing in this document, however, supersedes applicable laws and

regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 First article. When specified (see 6.2), a sample shall be subjected to first article

inspection in accordance with (see 4.2).

3.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or

environmentally preferable materials should be used to the maximum extent possible, provided

that the material meets or exceeds the operational and maintenance requirements, and promotes

economically advantageous life cycle costs.

3.3 Description. The coverall shall be a one-piece, unlined garment with a slide fastener

front fly closure with heavy duty plastic front slide fastener with double sliders, underarm

ventilation slide fasteners with thongs, reinforced knee, elbow and seat patches. The front shall

have slanted front chest pockets with two pieces of 5-1/4 inch long by 1-inch wide loop fastener

tape placed (as indicated on patterns) for placement of U.S. Army tape and nametape. The

coveralls also have a piece of 2-inch by 2-inch loop tape placed on front flap (as indicated on

patterns) for placement of rank, and a piece of 4-inch long by 2-inch wide loop tape on right

sleeve (as indicated on patterns) for placement of U.S. Flag. The coveralls have lower front

patch pockets with pass throughs. Hook and loop fastener tape adjustment tabs for the sleeves

and leg bottoms. Additional loop tape is required at sleeve and ankles to correspond with hook

on tabs when in the relaxed position. The waistband shall have elastic webbing in the center

back tunnel. Other pockets include hip pockets with hook and loop closures and a bellowed

utility pocket on left sleeve with loop placed on the front of the flap and pocket (as indicated on

patterns) for placement of unit patch, with a hook closure.

3.4 Material.

Provided by IHS

Licensed by www.sepana.ir

Sale only by www.sepana.ir, 05/22/2014 00:28:24 MDT

No reproduction or networking permitted without license from IHS

--`,`,``,`,`,``,,`,```,,,`,,`,,`-`-`,,`,,`,`,,`---

daneshlink.com

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

摘要：

MIL-DTL-32082A 是一项美国军用详细规范，适用于特定类型的无缝或焊接金属管材，主要用于航空航天及国防系统的液压、燃油及气动管线。该标准替代了早期版本，并明确了材料、尺寸公差、力学性能、无损检测及表面处理等要求，确保管材在极端温度、高压及腐蚀环境下具备高可靠性与互换性。对于军工供应链企业及采购工程师而言，掌握 MIL-DTL-32082A 内容有助于合规选材、减少验证成本并满足军品承包资质审核。

展开>> 收起<<

MIL-DTL-32082A.pdf

共16页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

MIL-DTL-32082A

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: