MIL-T-15005F

VIP专免
standardshare 2025-06-15 7 582.85KB 13 页 14星币
侵权投诉
INCH-POUNDI
MIL-T-
15005F
06
DECEMBER
1989
SUPERS
Eûi
NG
9
July
1962
(See
6.5)
MIL-T-
1500%
MILITARY
SPECIFICATION
TUBES,
CONDENSER
AND
HEAT
EXCHANGER,
COPPER-NICKEL
ALLOYS
(UNS
C70600
&
C71500)
This
specification
is
approved
for
use
by
all
Departments and
Agencies
of
the
Department
of
Defence.
1.
SCOPE
1.1
Scope.
This
specification
covers
copper-nickel
alloy
condenser
and
heat
exchanger
tubes
for
sea
water
service.
1.2
Classificarion.
Tubes
shall
be
furnished
in
the
following
compositions
and
tempers,
as
specified
(see
6.2).
When
no
temper
is
specified, tubes shall
be
supplied
in
che
annealed
condition.
Composition:
Copper
alloy
C70600
(Formerly 90-10)
Copper
alloy
C71500
(Formerly
70-30)
Temper:
C70600
-
061
-
Annealed
C71500
-
061
-
Annealed
i455
-
Light
drawn
HR50
-
Dram,
stress
relieved
Beneficial
commentc
(recommendations,
additions,
deletions)
and
any
pertinent
data
which
may
be
of
use
in
improving
this
document
should
be
addressed
to:
Commander,
Naval
Sea
Systems
Command,
SEA
5523,
Department
of
the
Navy,
Washington,
DC
20362-5101
by
using
the
self-addressed
Standardization
Document
Improvement
Proposal
(DD
Form
1426)
appearing
at
the
end
of
this
documenc
or
by
letter.
AMSC
N/A
DISTRIBUTION
STATEMENT
A,
Approved
for
public release; distribution
is
unlimited.
FSC
t7LO
Provided by IHS
Licensed by www.sepana.ir
Sale for only by www.sepana.ir, 05/25/2014 17:04:34 MDT
No reproduction or networking permitted without license from IHS
--``,````,,``,`,```,`,,```,-`-`,,`,,`,`,,`---
daneshlink.com
daneshlink.com
2.
APPLICABLE DOCUMENTS
2.1
Government
ducumencs.
2.1.1
Specifications. standards.
and
handbooks.
The
following
specifi-
cations,
standards,
an8
handbooks
form
a part
of
this document to the extent
specified herein. Unless otherwise specified, the
issues
of
these documents are
those listed
in
the issue
of
the
Department
of
Defence
Index
of
Specifications and
Standards
(DODISS)
and supplement thereto, cited
in
the solicitation
(see
6.2).
STANDARDS
MI
LI
TARY
MIL-STD-271
-
Requirements
for
Nondestructive Testing Methods.
MIL-STD-797
-
IdentíficatLon Marking Requirements
for
Special
Purpose
Components.
(Unless otherwise indicated,
copies
of
federal
and
military
specifications,
standards,
and
haníibooks
are avaiia'bie from
the
Navai Publications end Forms
Center,
(ATTN:
NPODS),
5801
Tabor
Avenue, Philadelphia,
PA
19120-5099.)
2.2
Non-Government
publications.
The
following
document(c)
form
a
part
of
this document to the extent specified herein. Unless
otherwise
specified,
the
issues
of
the
documents
which
are
DOD adopted are
those
listed
in
the issue of
the
DODISS
cited in
the
solicitation. Unless otherwise specified, the
issues
of
documents
not
listed
in
the
DODTSS
are
the issues
of
the
documents
cited
in
the
solicitation
(see
6.2).
AMERICAN
SOCIETY
FOR
TESTING
AND
MATERIALS
(ASTH)
B
111
-
Standard Specification for Copper and Copper-Alloy Seamless
Condenser
Tubes
and Ferrule
Stock.
(DoD
adopted)
B
153
-
Standard Test Method
for
Expansion
(Pin
Test)
of
Copper and
Copper-Alloy
Pipe and Tubing.
E
243
-
Standard
Practice
for
Electromagnetic (Eddy-Current)
Testing of
Seamless
Copper
and
Copper Alloy
Tubes.
(DoD
adopted)
(Application
for
copies
should
be
addressed
Co
the
American
Society
for
Testing and Materials, 1916
Race
Street, Philadelphia,
PA
19103.)
(Non-Government standards and other publications
are
normally available
from
the organizations
that
prepare
or
distribute
the
documents. These documents
also
may
be
available
in
or
through
libraries
or
other informational services.)
2.3
Order
of
vrecedence.
In
the
event
of
a
conflict
between
the
text
of
this
document
and
the references
cited
herein, the text
of
this
document takes
precedence. Nothing
in
this document, however, supersedes
applicable
laws and
regulations
unless
a
specific exemption has
been
obtained.
n
L
Provided by IHS
Licensed by www.sepana.ir
Sale for only by www.sepana.ir, 05/25/2014 17:04:34 MDT
No reproduction or networking permitted without license from IHS
--``,````,,``,`,```,`,,```,-`-`,,`,,`,`,,`---
daneshlink.com
daneshlink.com
I
I
HIL-T-
15005F
3.
REQUIREMENTS
I
I
3.1
Bateriai.
Copper
alloys
C70600
and
C71500 condenser tubes shall conform
to
ASTH
B
111
(see
6.2)
with supplementary requirements
52,
53
and
Sb
as
modified
herein.
3.1.1 pecovered materíars.
Unless
otherwise specified herein, material
covered by this specification shall be new and may
be
produced
from
recovered
materials to the maximum extent possible without jeopardizing the intended use.
The term recovered materials means materials which have been collected
OK
recovered
from
solid waste and reprocessed to become a source
of
raw materials, as
opposed
to
virgin
rau
materials.
that the use
of
rebuilt products is allowed under this specification unless
specifically specified.
None
of
the
above
shall be interpreted
to
mean
3.2
Chemicalanelucis.
Chemical analysis
of
the tube shall conform
to
that
in
ASTM
B
111
including the tighter trace element limits listed
HS
applicable to
material for subsequent welding applications.
3.3
Mechanical prorierties and grain size.
Tubes
shall
conform
to
the
requirements
of
ASTH
B
111
for
flatteningand grain size. When specified (see
6.2),
tubes shall conform to the mechanical property requirements of
ASTH
B
111.
Tubes shell meet the expansion test requirements
of
this specification.
3.4
Soundness.
Tubes
shall
be
of
uniform
temper,
free
of
grooves,
indentations, cracks, laps and blisters to the extent determinable by visual
or
nondestructive testing. Nondestructive testing
shall
be by eddy current and
hydrostatic cests to
ASTM
B
111. üñen specified (see
6.2).
tubes
shall
be
hydrostatic tested by
the
requirements.of
ASTM
E
111,
ultrasonic tested
to
the
requirements
of
6.6.3,
and 'liquid penetrant inspected in accordance with
4.4.2.
3.5
Cleanliness. The inner and outer surface of the tube shall be delivered
clean, free
of
dirt,
oils,
grease, acid, chips, carbonaceous material,
free
carbon,
sulfur
bearing compounds
or
any
other
foreign material that render the
tubes
unfit
for
cheir intended use.
compounds,
carbon
of
carbon
bearing
Compounds,
from
lubricants used
in
forming,
machining
or
other processing and marking materials used
for
in-process identifi-
cation shall
be
removed
from
the material
prior
to
any
hear: treatment.
shall
be
cleaned either by acid pickling after heat treating
or
by using.an inert
or
reducing atmosphere during heat treatment. All trace
of
acid
shall
be
removed
following acid cleaning.
Contaminants
such
as sulfur
or
sulfur bearing
Tubing
3.5.1
Mercury ccntamlnatioq. ïhe tubes shell be free
of
all
contamination.
During
the
manufacturing
processes,
tests,
and
inspections the product
to
be
offered
for
acceptance shall not have
come
into direct contact
with
mercury or
any
of
its compounds
nOK
vith any
mercury
hearing
device
employing
a
single
boundary
of
containment.
3.6
Dimensions.
Dimensions
of
the tube
shall
be as specified (diameter,
wall thickness and length) (see
6.2).
The outside diameter tolerances for tubes
acquired
to
this
specificatim
shall
be
as
specified
in
ASiM
B
111,
Ixit
shall
be
all
m
the
minus
side.
Tubes
shall
be
supplied
to
minimum
wail
requirements of
ASTM
B
111.
3
Provided by IHS
No reproduction or networking permitted without license from IHS
--``,````,,``,`,```,`,,```,-`-`,,`,,`,`,,`---
daneshlink.com
daneshlink.com
摘要：

MIL-T-15005F 是美国军用标准规范，用于定义无缝或焊接的碳钢和合金钢管的制造、检验与交货要求。该标准主要涵盖低温环境或一般结构用途的机械钢管，适用于液压系统、燃料管线及气动设备等关键军事应用场景。MIL-T-15005F 详细规定了化学成分、力学性能、公差尺寸、热处理工艺以及无损检测等质量控制条款，确保产品在严苛环境下具备高可靠性和互换性。文档标题中的“F”代表修订版本号，表明该规范已多次更新以适应当代国防装备的制造需求。理解 MIL-T-15005F 对于采购、质检及工程设计人员选择

展开>> 收起<<
MIL-T-15005F.pdf

共13页,预览3页

还剩页未读， 继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

相关推荐

更多
立即下载
作者：standar... 分类：国外协会 价格：14星币 属性：13 页 大小：582.85KB 格式：PDF 时间：2025-06-15

开通VIP享超值会员特权

  • 多端同步记录
  • 高速下载文档
  • 免费文档工具
  • 分享文档赚钱
  • 每日登录抽奖
  • 优质衍生服务

相关内容

更多

热门标签

ISO 混凝土 技术规范 检验 航空航天 不锈钢 消防 压力容器 铝合金 法兰
/ 13
评分 收藏
分享
立即下载 VIP免费下载
客服
关注