ASTM C1032 - 18

VIP免费

Carl 2024-09-02 13 79.03KB 3 页 10星币

Designation: C1032 −18
Standard Speciﬁcation for
Woven Wire Plaster Base
1
This standard is issued under the ﬁxed designation C1032; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This speciﬁcation covers woven wire plaster base, ﬂat or
self-furring, with or without stiffener wires, and with or
without factory-attached water-resistive barrier, designed for
use as a base to receive gypsum or portland cement based
plaster.
1.2 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
and are not considered standard.
1.3 The text of this standard references notes and footnotes
which provide explanatory material. These notes and footnotes
(excluding those in tables and ﬁgures) shall not be considered
as requirements of the standard.
1.4 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
2
A641/A641M Speciﬁcation for Zinc–Coated (Galvanized)
Carbon Steel Wire
C11 Terminology Relating to Gypsum and Related Building
Materials and Systems
E2556/E2556M Speciﬁcation for Vapor Permeable Flexible
Sheet Water-Resistive Barriers Intended for Mechanical
Attachment
2.2 Federal Speciﬁcations:
UU-B-790a Building Paper, Vegetable Fiber: Kraft,
Waterproofed, Water Repellent and Fire Resistant
3
UU-P-31 B/171 Tensile Breaking Strength (Dry)
3
3. Terminology
3.1 Deﬁnitions—Deﬁnitions shall be in accordance with
Terminology C11.
4. Material
4.1 In accordance with Speciﬁcation A641/A641M and
Table 1.
4.2 Water-resistive Barrier—Compliant with Federal Speci-
ﬁcation UU-B-790a or ASTM Speciﬁcation E2556/E2556M.
4.3 Kraft Building Paper, Federal Speciﬁcation UU-B-790a.
5. Physical Properties
5.1 Water-resistive Barrier:
5.1.1 Factory-attached water-resistive barrier shall provide a
one mesh wire to wire lap joint at one end and one edge of each
ﬂat sheet or roll. Attachment of the water-resistive barrier shall
allow lapping of wire-to-wire and water-resistive barrier to
water-resistive barrier of one mesh at ends and edges and shall
permit full embedment in not less than
1
⁄
4
in. (6.4 mm) of
plaster of not less than one half the total length and width of the
wire.
5.1.2 Factory-attached water-resistive barrier shall have a
minimum tensile breaking strength (dry) of 20 lbf/in.
(3.5 kN ⁄m) width, as tested in accordance with Federal Speci-
ﬁcation UU-P-31 B, Method 171.
6. Dimensions, Weight, and Permissible Variations
6.1 Openings:
6.1.1 Woven wire plaster base shall be fabricated to provide
the size of openings in accordance with Table 1, except that any
single opening shall be not more than 3.0 in.
2
(1935.5 mm
2
).
6.1.2 Wire diameter for opening size shall be in accordance
with Table 1.
1
This speciﬁcation is under the jurisdiction of ASTM Committee C11 on
Gypsum and Related Building Materials and Systems and is the direct responsibility
of Subcommittee C11.02 on Speciﬁcations and Test Methods for Accessories and
Related Products.
Current edition approved Oct. 1, 2018. Published October 2018. Originally
approved in 1985. Last previous edition approved in 2014 as C1032 – 14. DOI:
10.1520/C1032-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
.Available from U.S. Government Printing Office Superintendent of
Documents, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401,
http://www.access.gpo.gov.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
 

6.2 Diameter tolerance for galvanized wire shall be in

accordance with Speciﬁcation A641/A641M.

6.3 The wire shall be zinc-coated (galvanized) in accor-

dance with Speciﬁcation A641/A641M.

6.4 Weight for woven wire plaster base shall be in accor-

dance with Table 1.

6.5 When included as part of the woven wire plaster base,

factory fabricated stiffener wires shall have a diameter not less

than that speciﬁed in Table 1 and shall be continuous, parallel

to the long dimension of the plaster base, and shall occur at not

more than 6-in. (154.4-mm) intervals.

6.6 Factory fabricated crimps for self-furring woven wire

plaster base shall provide a nominal

⁄

-in. (6.4-mm) separation

between the back plane of the plaster base and the surface of

solid backing to permit embedment in both directions.

6.7 Width of woven wire plaster base shall be not less than

36 in. (914 mm).

6.8 Length of woven wire plaster base shall be in accor-

dance with Table 2.

7. Inspection

7.1 Inspection of the material shall be agreed upon between

the purchaser and the producer or supplier as part of the

purchase agreement.

8. Rejection and Rehearing

8.1 Material that fails to conform to the requirements of this

speciﬁcation shall be reported to the producer or supplier

promptly and in writing. The notice of rejection shall contain a

statement documenting how the product has failed to conform

to the requirements of the speciﬁcation.

9. Certiﬁcation

9.1 When speciﬁed in the purchase order or contract, the

producer or supplier shall furnish a report certifying that at the

time of shipment, the materials were in compliance with the

requirements of this speciﬁcation.

10. Packaging and Package Marking

10.1 Packaging—Woven wire plaster base shall be pack-

aged in bundles, rolls or pallets.

10.2 Marking—Unless otherwise required by the purchase

agreement, lath shall have legibly marked thereon the follow-

ing: the product description; the name of the manufacturer or

distributor, country of origin and contact information; the

brand name (if any); and the ASTM designation for the

product.

10.2.1 Each bundle or roll of lath without factory-attached

water-resistive barrier shall be marked with metal or paper tags

securely attached to the bundles or with metal tags, paper tags,

plastic or metal banding or paper wrapping on rolls.

10.2.2 Each ﬂat sheet and roll of lath with factory-attached

water-resistive barrier shall be marked on the water-resistive

barrier or face paper attached to the water-resistive barrier.

10.2.3 The quantity for ﬂat sheet bundles shall be square

yards and number of sheets per bundle marked with metal or

paper tags on the pallet or bundle. Rolls shall be marked with

metal tags, paper tags, plastic or metal banding or paper

wrapping on rolls. The marking for ﬂat sheets and rolls shall

indicate the mesh-opening size and wire thickness of rolls.

11. Keywords

11.1 water-resistive barrier; base; cement plaster; ﬂat; gyp-

sum plaster; plaster; self-furning; water-resistive barrier; wo-

ven wire

SUMMARY OF CHANGES

Committee C11 has identiﬁed the location of selected changes to this standard since the last issue (C1032 – 14)

that may impact the use of this standard. (Approved Oct. 1, 2018.)

(1) Added Speciﬁcation E2556/E2556M to list of referenced

documents (Section 2).

(2) Replaced the word “backing” with “factory-attached water

resistive barrier” or “water-resistive barrier” throughout.

(3) Added new 4.2 and renumbered subsequent sections ac-

cordingly.

TABLE 1 Nominal Diameter and Minimum Weight for Size of

Opening

Opening Size, in. (mm) Diameter, in. (mm) Weight, lb/yd

(kg/m

)

1 (25.4) 0.035 (0.89) 0.86 (0.466)

⁄

(38.0) 0.051 (1.30) 1.40 (0.760)

The weight of attached backing is not included.

TABLE 2 Minimum Length of Flat Sheets and Rolls

Flat Sheets 100 linear in. (2.540 m)

Rolls 150 linear ft. (45.72 m)

Rolls, with backing 100 linear ft. (30.48 m)

Allowable variations shall be not more than −

⁄

in. (−19.0 mm) in width or length.

C1032 − 18

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned

in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk

of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ﬁve years and

if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards

and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the

responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should

make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,

United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above

address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website

(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222

Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/

C1032 − 18

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

已全部加载

摘要：

ASTM C1032 - 18 是由美国材料与试验协会（ASTM）发布的一项标准规范，主要针对陶瓷纤维制品（包括毯、毡、纸和纺织品等）的型号、尺寸、物理性能和测试方法进行规定。该标准于2018年修订，涵盖了陶瓷纤维产品的容重、厚度、热稳定性、抗拉强度等关键指标，适用于工业高温隔热、炉衬、密封等应用场景。通过遵循 ASTM C1032-18，制造商和用户能够确保产品的性能一致性和质量控制，从而提升工程安全性和材料选型的可靠性。此标准是高温行业和耐火材料领域中重要的参考文件，对于采购、质检及研发人员

展开>> 收起<<

ASTM C1032 - 18.pdf

共3页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ASTM C1032 - 18

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: