MIL-DTL-3316D-2020 隔热用耐火胶粘剂

VIP免费

standardshare 2026-04-19 8 846.95KB 17 页 18星币

侵权投诉

Comments, suggestions, or questions on this document should be addressed to Commander, Naval Sea Systems

Command, ATTN: SEA 05S, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160

or emailed to CommandStandards@navy.mil, with the subject line “Document Comment”. Since contact

information can change, you may want to verify the currency of this address information using the ASSIST

Online database at https://assist.dla.mil.

AMSC N/A FSC 8040

DISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.

INCH-POUND

MIL-DTL-3316D

24 March 2020

SUPERSEDING

MIL-A-3316C

20 October 1987

DETAIL SPECIFICATION

ADHESIVES, FIRE-RESISTANT – FOR THERMAL INSULATION

This specification is approved for use by all Departments and Agencies of the Department of Defense.

1. SCOPE

1.1 Scope. This specification covers fire-resistant adhesives for securing cloth and tape to thermal insulations

and for securing thermal insulations to metal surfaces.

1.2 Classification. The adhesives are of the following classes and grades, as specified (see 6.2).

1.2.1 Classes. Classes of adhesives are as follows:

a. Class 1 – For bonding fibrous glass cloth to unfaced fibrous glass insulation, sealing the edges of and

bonding fibrous glass tape to the joints of fibrous glass board, and bonding lagging cloth to thermal insulation.

b. Class 2 – For attaching fibrous glass insulation to metal surfaces.

c. Class 3 – For attaching cork and fibrous glass insulation board to metal surfaces.

1.2.2 Grades. Grades of adhesives are as follows:

a. Grade A – Pigmented white.

b. Grade B – Pigmented red (sealer coating to identify asbestos-free system).

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This

section does not include documents cited in other sections of this specification or recommended for additional

information or as examples. While every effort has been made to ensure the completeness of this list, document

users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this

specification, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a

part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are

those cited in the solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-C-20079 - Cloth, Glass; Tape, Textile Glass; and Thread, Glass and Wire-Reinforced

Glass

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

MIL-DTL-3316D

MIL-DTL-24607 - Enamel, Interior, Nonflaming (Dry), Chlorinated Alkyd Resin, Semigloss

MIL-DTL-32585 - Insulation, Thermal and Acoustic, Fibrous Glass

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-1916 - DoD Preferred Methods for Acceptance of Product

(Copies of these documents are available online at https://quicksearch.dla.mil.)

2.2.2 Other Government documents, drawings, and publications. The following other Government documents,

drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified,

the issues of these documents are those cited in the solicitation or contract.

NAVAL SEA SYSTEMS COMMAND (NAVSEA) PUBLICATIONS

S9510-AB-ATM-010 - Nuclear Powered Submarine Atmosphere Control Manual

(Copies of the chapter titled “Material Control Program” are available by email request to

CommandStandards@navy mil.)

T9070-AK-DPC-010/078-1 - Composite Materials, Surface Ships, Topside Structural and Other

Topside Applications – Fire Performance Requirements

T9070-AL-DPC-020/077-2 - NAVSEA Hazardous Material Avoidance Process

(Copies of these documents are available online via Technical Data Management Information System (TDMIS) at

https://mercury.tdmis navy mil/ by searching for the document number without the suffix. Refer questions,

inquiries, or problems to: DSN 296-0669, Commercial (805) 228-0669. These documents are available for ordering

(hard copy) via the Naval Logistics Library (NLL) at https://nll navsup navy mil. For questions regarding the NLL,

contact the NLL Customer Service at nllhelpdesk@navy.mil, (866) 817-3130, or (215) 697-2626/DSN 442-2626.)

2.3 Non-Government publications. The following documents form a part of this document to the extent

specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or

contract.

ASTM INTERNATIONAL

ASTM D92 - Standard Test Method for Flash and Fire Points by Cleveland Open Cup

Tester

ASTM D217 - Standard Test Methods for Cone Penetration of Lubricating Grease

ASTM D522/D522M - Standard Test Methods for Mandrel Bend Test of Attached Organic

Coatings

ASTM D562 - Standard Test Method for Consistency of Paints Measuring Krebs Unit

(KU) Viscosity Using a Stormer-Type Viscometer

ASTM D823 - Standard Practices for Producing Films of Uniform Thickness of Paint,

Coatings and Related Products on Test Panels

ASTM D903 - Standard Test Method for Peel or Stripping Strength of Adhesive Bonds

ASTM D1475 - Standard Test Method for Density of Liquid Coatings, Inks, and Related

Products

ASTM D2196 - Standard Test Methods for Rheological Properties of Non-Newtonian

Materials by Rotational Viscometer

ASTM D2486 - Standard Test Methods for Scrub Resistance of Wall Paints

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

MIL-DTL-3316D

ASTM D3891 - Standard Practice for Preparation of Glass Panels for Testing Paint,

Varnish, Lacquer, and Related Products

ASTM E662 - Standard Test Method for Specific Optical Density of Smoke Generated by

Solid Materials

(Copies of these documents are available online at www.astm.org.)

INTERNATIONAL MARITIME ORGANIZATION (IMO)

Fire Test Procedures (FTP) Code - International Code for Application of Fire Test Procedures

(Copies of this document are available online at www.imo.org.)

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO)

ISO/IEC 17025 - General Requirements for the Competence of Testing and Calibration

Laboratories

(Copies of this document are available online at www.iso.org.)

SAE INTERNATIONAL

SAE-AMS-STD-595/31158 - Colors Used in Government Procurement; Red, Flat (Light Red

International)

(Copies of this document are available online at www.sae.org.)

TECHNICAL ASSOCIATION OF THE PULP AND PAPER INDUSTRY (TAPPI)

TAPPI T 803 - Puncture Test of Container Board

(Copies of this document are available online at www.tappi.org.)

2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between

the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this

document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 Qualification. The adhesives furnished under this specification shall be products that are authorized by the

qualifying activity for listing on the applicable qualified products list before contract award (see 4.2 and 6.3).

3.2 Material. The adhesive shall meet the requirements herein without heating or the addition of other

ingredients and shall be free of all ingredients that may adversely affect serviceability, have a deleterious effect on

thermal insulation and fibrous glass cloth, or corrode bare steel in adhesion tests or primed steel in service.

Adhesives shall not contain mercury or mercury compounds and shall be asbestos free.

3.3 Stability.

3.3.1 Storage stability. The adhesives shall meet all of the requirements specified herein when tested as

specified in 4.6.3.1.

3.3.2 Freeze-thaw stability. The adhesive shall meet the requirements specified herein when tested as specified

in 4.6.3.2.

3.4 Toxicity. When evaluated in accordance with 4.6.4, the adhesive shall pose no serious or high risk to the

health of personnel or the environment when used for its intended purpose (see 4.6.4 and 6.7).

3.5 Prohibited materials. The adhesive shall not contain any chemicals categorized as “prohibited” in

accordance with T9070-AL-DPC-020/077-2.

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #隔热

摘要：

本页面详细介绍 MIL-DTL-3316D-2020 标准规范，该标准针对隔热用耐火胶粘剂的性能、测试方法和应用要求进行了最新修订。此规范由美国国防部发布，确保胶粘剂在高温、火焰暴露及极端环境下的粘结稳定性与隔热效果，适用于航空航天、舰船、军事及工业隔热系统。内容涵盖材料成分、耐温等级、老化试验、施工工艺及认证指南，旨在帮助工程师、采购人员和质检团队精准选择合规产品，保障设备安全与可靠性。

展开>> 收起<<

MIL-DTL-3316D-2020 隔热用耐火胶粘剂.pdf

共17页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

MIL-DTL-3316D-2020 隔热用耐火胶粘剂

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: