MIL-DTL-6001B_AMENDMENT-1 飞机用焊接型管配件

VIP免费

standardshare 2026-04-19 23 230.3KB 9 页 18星币

侵权投诉

AMSC N/A FSC 4730

MIL-DTL-6001B

13 February 2013

SUPERSEDING

MIL-F-6001A (ASG)

15 July 1958

DETAIL SPECIFICATION

FITTINGS; AIRCRAFT, SOLDER TYPE, TUBE

This specification is approved for use by all Departments and

Agencies of the Department of Defense.

1. SCOPE

1.1 Scope. This specification covers the general requirements for fittings, aircraft, solder type, tube.

1.2 Part or Identifying Number (PIN). The PIN requirements are shown in the specification sheets.

1.2.1 Air Force – Navy Aeronautical Standard. The specification sheets are listed in supplement 1.

1.2.2 Size of fittings. Sizes are shown in the individual specification sheets.

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3, 4 or 5 of this specification.

This section does not include documents cited in other sections of this specification or recommended for

additional information or as examples. While every effort has been made to ensure the completeness of

this list, document users are cautioned that they must meet all specified requirements documents cited in

sections 3, 4 or 5 of this specification, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks

form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

these documents are those cited in the solicitation or contract.

FEDERAL SPECIFICATIONS

QQ-N-281 Nickel-Copper-Alloy (Monel and R-Monel) Bars, Plates, Rods, Sheets, Strips,

Wire, Forgings, and Structural and Special Shaped Sections

Comments, suggestions, or questions on this document should be addressed to: DLA Land and Maritime, Attn: VAI,

P.O. Box 3990, Columbus, OH 43218-3990, or emailed to FluidFlow@dla.mil. Since contact information can change,

you may want to verify the currency of this address information using the ASSIST Online database at

https://assist.dla.mil.

INCH-POUND

Inactive for new design after 24 July 1998.

Source: https://assist.dla.mil -- Downloaded: 2015-07-28T13:39Z

Check the source to verify that this is the current version before use.

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

MIL-DTL-6001B

DEPARTMENT OF DEFENSE SPECIFICATIONS

(See supplement 1 for list of specification sheets.)

DEPARTMENT OF DEFENSE STANDARD

MIL-STD-129 Marking for Shipment and Storage

(Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from

the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia,

PA 19111-5094.)

2.3 Non-Government publications. The following documents form a part of this document to the extent

specified herein. Unless otherwise specified, the issues of documents are those cited in the solicitation or

contract.

ASTM INTERNATIONAL

ASTM B121/B121M Leaded Brass Plate, Sheet, Strip, and Rolled Bar, Standard Specification for

ASTM B154 Mercurous Nitrate Test for Copper Alloys, Standard Test Method for

ASTM B858 Ammonia Vapor Test for Determining Susceptibility to

Stress Corrosion Cracking in Copper Alloys, Standard Test Method for

(Copies of these documents are available online at http://www.astm.org or from the ASTM International,

P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.)

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO)

ISO 6957 Copper Alloys - Ammonia Test for Stress Corrosion Resistance First Edition

ISO 17025 General requirements for the competence of testing and calibration laboratories

ISO 19879 Metallic tube connections for fluid power and general use — Test methods for hydraulic

fluid power connections - Second Edition

(Copies of these documents are available online at www.ansi.org or from the ANSI Customer Service

Department, 25 W. 43rd Street, 4th Floor, New York, NY 10036.)

NCSL INTERNATIONAL

NCSL Z540.3 Requirements for the Calibration of Measuring and Test Equipment

(Copies of these documents are available online at http://www.ncsli.org or from NCSL International 2995

Wilderness Place, Suite 107 Boulder, Colorado 80301-5404)

SAE INTERNATIONAL

SAE AMS-QQ-P-416 Plating, Cadmium (Electrodeposited)

SAE AMS2700 Passivation of Corrosion Resistant Steels

SAE AMS-S-7720 Steel, Corrosion-Resistant (18-8) Bars, Wire and Forging Stock

(Aircraft Quality)

(Copies of these documents are available on line at www.sae.org from SAE International, 400

Commonwealth Drive, Warrendale, PA 15096-0001, and Tel: 877-606-7323 [inside USA and Canada] or

724-776-4970 [outside USA], email at CustomerService@sae.org.)

Source: https://assist.dla.mil -- Downloaded: 2015-07-28T13:39Z

Check the source to verify that this is the current version before use.

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

MIL-DTL-6001B

2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict

between this document and the references cited herein (except for related specification sheets) the text of

this document takes precedence. Nothing in this document, however, supersedes applicable laws and

regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 Specification sheets. The individual item requirements shall be as specified herein and in

accordance with the applicable specification sheet. In the event of any conflict between the requirements

of this specification and the specification sheet, the latter shall govern.

3.2 First article. When specified (see 6.2), samples shall be subjected to first article inspection in

accordance with 4.4.

3.3 Design and dimensions. The design and dimensions shall meet the requirements specified herein

and in the applicable AN or MS standard.

3.4 Shape and form restrictions. Abrupt reductions of section shall be avoided. Small external sections

adjoining relatively heavy body sections shall be shaded into the heavier sections by means of ample

fillets. Sharp corners or inadequate fillets, excessive undercuts or grooves, at the junction of such small

sections with large sections of fittings shall be considered cause for rejection. Unless otherwise

specified, drawing tolerances shall apply to fillet and corner radii.

3.5 Materials. Fittings shall be fabricated of materials listed in table I as specified on the applicable AN

or MS standard. TABLE I. Materials.

Materials Form Specification Number

Brass Bars, Rods, Shapes and Forging ASTM B121/B121M

Corrosion – Resistant

Steel (18Cr – 8Ni) Bars and Rods SAE AMS-S-7720

Nickel – Copper - Alloy Forging, Plates, Rods, Shapes,

Sheets, Strips and Wire QQ-N-281

3.5.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or

environmentally preferable materials should be used to the maximum extent possible, provided that the

material meets or exceeds the operational and maintenance requirements, and promotes economically

advantageous life cycle cost.

Source: https://assist.dla.mil -- Downloaded: 2015-07-28T13:39Z

Check the source to verify that this is the current version before use.

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #配件 #焊接 #管配件

摘要：

本文档详细介绍了美国军用标准MIL-DTL-6001B的第一次修订版（AMENDMENT-1），该标准专门规定了用于飞机及其他航空器的高可靠性焊接型管配件的材料、设计、制造工艺及质量验收要求。作为军事航空领域的关键技术规范，该修订版旨在更新并优化原有标准，确保焊接管配件在极端飞行环境下的密封性、强度与耐久性。内容涵盖了配件类型、焊接技术要求、尺寸公差、表面处理以及外采购方的检验标准，适用于飞机制造商、国防供应商及维修单位。通过遵循本规范，用户可确保所采用的管件符合军用级耐压、抗疲劳及抗腐蚀性能，从而提升整机系统的安全性与任务可靠性。本标准是飞机燃油、液压及气动系统中焊接管路组件设计与采购的核心依据。

展开>> 收起<<

MIL-DTL-6001B_AMENDMENT-1 飞机用焊接型管配件.pdf

共9页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

MIL-DTL-6001B_AMENDMENT-1 飞机用焊接型管配件

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: