ASTM F1074 - 87 (2023)

VIP免费

Carl 2024-09-04 11 270.92KB 3 页 14星币

Designation: F1074 −87 (Reapproved 2023) An American National Standard
Standard Speciﬁcation for
Cleats, Welded Horn Type
1
This standard is issued under the ﬁxed designation F1074; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This speciﬁcation covers hollow cleats and pads for
marine use.
1.2 The cleats shall be used where securing of boat handling
lines are required onboard commercial and navy boats and
crafts.
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
and are not considered standard.
1.4 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
2
A36/A36M Speciﬁcation for Carbon Structural Steel
A370 Test Methods and Deﬁnitions for Mechanical Testing
of Steel Products
A385 Practice for Providing High-Quality Zinc Coatings
(Hot-Dip)
3. Ordering Information
3.1 Orders for material under this speciﬁcation shall include
the following:
3.1.1 Title, number, and date of this speciﬁcation,
3.1.2 Quantity,
3.1.3 Size of cleats, and
3.1.4 Packaging, packing, or marking requirements.
4. Materials and Manufacture
4.1 Material:
4.1.1 The horn cleats shall be of galvanized steel, grade
1023W, in accordance with Practice A385.
4.1.2 The base plate shall be of steel, (carbon 0.35
maximum), in accordance with Speciﬁcation A36/A36M.
4.1.3 All chaﬁng surfaces shall have a 125µ ﬁnish.
4.2 Manufacture—The cleats’ horns shall be of cast steel,
round in shape, and free of burrs or sharp edges. The horns
shall be welded to a base plate as shown in Fig. 1 (see Table 1).
The weld is to be ground smooth to prevent chaﬁng of ropes.
The base plate shall be oval shaped with smooth rounded
edges. The dimensions shall be in accordance with Table 1.
5. Packaging
5.1 The packing shall afford protection against deterioration
and physical damage during shipment from the manufacturer to
the using activity for immediate use.
6. Product Marking
6.1 Containers shall be stenciled with the ASTM standard
designation, in black paint with approximately 1 in. (25.4 mm)
high letters and numbers with the following information:
6.1.1 Address,
6.1.2 purchase order number, and
6.1.3 Manufacturer’s name.
7. Keywords
7.1 base plates; boat handling lines; cleats; hollow cleats;
horn cleats; marine; marine cleats; ship; welded cleats
1
This speciﬁcation is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outﬁtting and Deck Machinery.
Current edition approved July 1, 2023. Published July 2023. Originally approved
in 1987. Last previous edition approved in 2018 as F1074 – 87 (2018). DOI:
10.1520/F1074-87R23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1

NOTE 1—See Table 1 for dimensions.

FIG. 1 Welded Horn Type Cleat (16 in.)

F1074 − 87 (2023)

SUPPLEMENTARY REQUIREMENTS

The following supplementary requirement shall apply only when speciﬁed by the purchaser in the

contract or order.

S1. Quality Assurance Provisions

S1.1 Responsibility for Inspection—The purchaser reserves

the right to perform any of the inspections set forth in the

speciﬁcation where such inspections are deemed necessary to

assure that supplies and services conform to prescribed require-

ments.

S1.2 Source Inspection—The purchaser reserves the right

to inspect the manufacturing process and end product in the

supplier‘s plant.

S1.3 Tests—The cleats shall meet the test load requirements

of Table 1, as tested in accordance with Test Methods and

Deﬁnitions A370.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned

in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk

of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ﬁve years and

if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards

and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the

responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should

make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,

United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above

address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website

(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222

Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/

TABLE 1 Welded Horn-Type Cleat Dimensions

NOTE 1—Table 1 is to be used with Fig. 1.

NOTE 2—1 in. = 25.4 mm.

NOTE 3—1 lb = 0.45 kg.

Cleat Rope Circumference (in.)

Rope Di-

ameter

(in.)

Cleats Test

Load (lb)

Dimensions (in.)

Calcu-

lated

Weight

(lb)

Manila Nylon Dacron Polypro-

pylene

6 × 37 Fi-

ber

Core Wire

Rope

A B C D E F G H J K L M N

10 2

⁄

32 5

⁄

16 1

⁄

2 5.3 1

⁄

1 1 1

⁄

4100

16 4 3 5 2

⁄

1 1

⁄

16 3

⁄

21.7 3 2 2 2

⁄

9000

24 6 4

⁄

75 5 3 3 4

⁄

23 000

30 7

⁄

415

⁄

815

⁄

16 7

⁄

137 6 3

⁄

4 5

⁄

36 000

F1074 − 87 (2023)

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

已全部加载

摘要：

ASTM F1074 - 87 (2023) 是美国材料与试验协会发布的关于碳钢及合金钢无缝管与焊接管的标准规范，该标准于1987年首次发布，并于2023年进行了最新确认，旨在为管道系统的设计、制造和检验提供统一的技术要求。该规范涵盖了管道的尺寸、壁厚、化学成分、力学性能以及无损检测等关键指标，适用于石油、化工、能源及建筑等行业的压力管道和结构应用。遵循ASTM F1074标准可确保管道产品在高温、高压及腐蚀性环境下的可靠性与安全性，帮助工程师和采购方有效筛选符合国际质量要求的管材。对于从事管道

展开>> 收起<<

ASTM F1074 - 87 (2023).pdf

共3页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ASTM F1074 - 87 (2023)

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: