ISO 2433-1999

VIP免费
阿拉丁 2024-09-08 8 271.22KB 38 页 12星币
侵权投诉
Reference number
ISO 2433:1999(E)
©ISO 1999
INTERNATIONAL
STANDARD ISO
2433
Third edition
1999-12-15
Machine tools — Test conditions for
external cylindrical and universal grinding
machines with a movable table — Testing
of the accurac
y
Machine-outils — Conditions d'essai des machines à rectifier les surfaces
de révolution extérieures et à rectifier universelles à table mobile —
Contrôle de la précision
Copyright International Organization for Standardization
Provided by IHS under license with ISO
Not for Resale
No reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
ISO 2433:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 ·CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved
Copyright International Organization for Standardization
Provided by IHS under license with ISO
Not for Resale
No reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
ISO 2433:1999(E)
© ISO 1999 – All rights reserved iii
Contents Page
1 Scope ..............................................................................................................................................................1
2 Normative references ....................................................................................................................................1
3 Description, terminology, and designation of axes ...................................................................................2
3.1 Description of machines...............................................................................................................................2
3.2 Terminology and designation of axes.........................................................................................................3
4 Preliminary remarks ......................................................................................................................................4
4.1 Measuring units .............................................................................................................................................4
4.2 Reference to ISO 230-1..................................................................................................................................4
4.3 Testing sequence...........................................................................................................................................4
4.4 Tests to be performed ...................................................................................................................................4
4.5 Measuring instruments .................................................................................................................................4
4.6 Machining tests..............................................................................................................................................4
4.7 Minimum tolerance for geometric tests ......................................................................................................4
5 Geometric tests..............................................................................................................................................5
5.1 Linear axes of motion....................................................................................................................................5
5.2 Workhead........................................................................................................................................................8
5.3 Tailstock .......................................................................................................................................................11
5.4 Wheelhead....................................................................................................................................................14
5.5 Swivel motions (Tests apply for swivelling component only) ...............................................................17
5.6 Internal grinding spindle.............................................................................................................................20
6 Machining tests............................................................................................................................................23
7 Accuracy and repeatability of positioning................................................................................................25
7.1 Positioning of manual or automatic (but not numerically controlled) linear axes ...............................25
7.2 Positioning of numerically controlled linear axes....................................................................................26
7.3 Positioning of numerically controlled rotary axes...................................................................................30
Annex A (informative) Equivalent terms in German and Italian ...........................................................................31
Bibliography..............................................................................................................................................................32
Copyright International Organization for Standardization
Provided by IHS under license with ISO
Not for Resale
No reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---

标签： #ISO

摘要：

本页面介绍国际标准 ISO 2433-1999，该标准全称为《机床—卧式铣床的精度检验》，主要规定了卧式铣床几何精度和工作精度的检验方法与公差要求。该标准适用于普通精度等级的卧式铣床，内容涵盖主轴、工作台、导轨等关键部件的检验项目及允差数值，为机床制造商、质量检验人员及用户提供统一的技术依据，确保设备加工的一致性与可靠性。ISO 2433-1999 替代了先前版本，是机械制造与机床行业国际标准化的重要参考文件。

展开>> 收起<<
ISO 2433-1999.pdf

共38页,预览4页

还剩页未读， 继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

相关推荐

更多
立即下载
作者：阿拉丁 分类：国际标准 价格：12星币 属性：38 页 大小：271.22KB 格式：PDF 时间：2024-09-08

开通VIP享超值会员特权

  • 多端同步记录
  • 高速下载文档
  • 免费文档工具
  • 分享文档赚钱
  • 每日登录抽奖
  • 优质衍生服务

相关内容

更多

热门标签

ISO 混凝土 技术规范 检验 航空航天 不锈钢 消防 压力容器 铝合金 法兰
/ 38
评分 收藏
分享
立即下载 VIP免费下载
客服
关注