ISO 10081-1-2003

VIP免费

阿拉丁 2024-09-09 7 167.58KB 8 页 12星币

侵权投诉

INTERNATIONAL

STANDARD ISO

10081-1

Second edition

2003-12-01

Reference number

ISO 10081-1:2003(E)

Classification of dense shaped refractory

products —

Part 1:

Alumina-silica

Classification des produits réfractaires façonnés denses —

Partie 1: Silice-alumine

Provided by IHS under license with ISO

Not for Resale

No reproduction or networking permitted without license from IHS

--`,,`,-`-`,,`,,`,`,,`---

ISO 10081-1:2003(E)

PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall

not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.

Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the

unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.

ISO copyright office

Case postale 56 • CH-1211 Geneva 20

Tel. + 41 22 749 01 11

Fax + 41 22 749 09 47

E-mail copyright@iso.org

Web www.iso.org

Published in Switzerland

Provided by IHS under license with ISO

Not for Resale

No reproduction or networking permitted without license from IHS

--`,,`,-`-`,,`,,`,`,,`---

ISO 10081-1:2003(E)

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 10081-1 was prepared by Technical Committee ISO/TC 33, Refractories.

The various parts of this revised series of ISO 10081 will cancel and replace ISO 1109:1975. Part 1 is a partial

revision of ISO 1109:1975, Part 2 cancels and replaces ISO 10081-1:1991, and Part 3 is new.

ISO 10081 consists of the following parts, under the general title Classification of dense shaped refractory

products:

—Part 1: Alumina-silica

—Part 2: Basic products containing less than 7 % residual carbon

—Part 3: Basic products containing from 7 % to 50 % residual carbon

Part 4 is under preparation and is intended to cover special products as given in Clause 2 of ISO 1109:1975.

Provided by IHS under license with ISO

Not for Resale

No reproduction or networking permitted without license from IHS

--`,,`,-`-`,,`,,`,`,,`---

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #ISO

摘要：

ISO 10081-1-2003 是国际标准化组织发布的关于致密定形耐火制品分类的国际标准，属于 ISO 10081 系列标准的第一部分。该标准规定了致密定形耐火制品的分类原则和方法，基于其化学矿物组成、主要成分以及使用温度范围进行分类，为耐火材料的选用、测试和质量控制提供了统一的国际规范。标准适用于各种工业窑炉中使用的耐火砖、浇注料预制块等致密定形制品，帮助用户准确识别和选择适合特定高温工况的材料。该版本于2003年发布，替代了之前的 ISO 10081-1 早期版本，对于从事耐火材料研发、生

展开>> 收起<<

ISO 10081-1-2003.pdf

共8页,预览4页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ISO 10081-1-2003

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: