API RP 11G-2013 (2019)

VIP免费

Carl 2024-08-26 26 504.43KB 34 页 14星币

侵权投诉

Recommended Practice for

Installation, Maintenance, and

Lubrication of Pumping Units

API RECOMMENDED PRACTICE 11G

FIFTH EDITION, NOVEMBER 2013

REAFFIRMED, JULY 2019

Special Notes

API publications necessarily address problems of a general nature. With respect to particular circumstances, local,

state, and federal laws and regulations should be reviewed.

Neither API nor any of API's employees, subcontractors, consultants, committees, or other assignees make any

warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the

information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any

information or process disclosed in this publication. Neither API nor any of API's employees, subcontractors,

consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.

Classified areas may vary depending on the location, conditions, equipment, and substances involved in any given

situation. Users of this specification should consult with the appropriate authorities having jurisdiction.

Users of this specification should not rely exclusively on the information contained in this specification. Sound

business, scientific, engineering, and safety judgment should be used in employing the information contained herein

API is not undertaking to meet the duties of employers, service providers, or suppliers to warn and properly train and

equip their employees, and others exposed, concerning health and safety risks and precautions, nor undertaking their

obligations to comply with authorities having jurisdiction.

Information concerning safety and health risks and proper precautions with respect to particular materials and

conditions should be obtained from the employer, the service provider or supplier of that material, or the material

safety datasheet.

API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the

accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or

guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or

damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may

conflict.

API publications are published to facilitate the broad availability of proven, sound engineering and operating

practices. These publications are not intended to obviate the need for applying sound engineering judgment

regarding when and where these publications should be utilized. The formulation and publication of API publications

is not intended in any way to inhibit anyone from using any other practices.

Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard

is solely responsible for complying with all the applicable requirements of that standard. API does not represent,

warrant, or guarantee that such products do in fact conform to the applicable API standard.

electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the

Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.

Foreword

Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the

manufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anything

contained in the publication be construed as insuring anyone against liability for infringement of letters patent.

Shall:As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification.

Should:As used in a standard, “should” denotes a recommendation or that which is advised but not required in order

to conform to the specification.

This document was produced under API standardization procedures that ensure appropriate notification and

participation in the developmental process and is designated as an API standard. Questions concerning the

interpretation of the content of this publication or comments and questions concerning the procedures under which

this publication was developed should be directed in writing to the Director of Standards, American Petroleum

Institute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any part

of the material published herein should also be addressed to the director.

Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time

extension of up to two years may be added to this review cycle. Status of the publication can be ascertained from the

API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published

annually by API, 1220 L Street, NW, Washington, DC 20005.

Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW,

Washington, DC 20005, standards@api.org.

iii

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

摘要：

API RP 11G-2013 (2019) 是美国石油协会发布的关于往复式泵及相关设备安装、操作与维护的推荐实践标准。该标准主要针对石油和天然气行业中使用的往复式泵（包括动力泵和直接作用泵），提供了从设计选型、安装基础、管道连接、驱动装置匹配到试运行和日常维护的全流程技术指导。2019年确认版保留了2013版的全部技术内容，同时确认其持续有效性。对于从事泵系统设计、现场工程、设备管理及维护的专业人员而言，该标准是确保泵组可靠性、减少停机时间和延长设备寿命的关键参考文件。它涵盖了泵振动分析、密封

展开>> 收起<<

API RP 11G-2013 (2019).pdf

共34页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

API RP 11G-2013 (2019)

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: