ISO 10893-5-2011

VIP免费

阿拉丁 2024-09-09 41 362.73KB 14 页 12星币

侵权投诉

Reference numbe

ISO 10893-5:2011(E)

INTERNATIONAL

STANDARD

ISO

10893-5

First edition

2011-04-01

Non-destructive testing of steel tubes —

Part 5:

Magnetic particle inspection of seamless

and welded ferromagnetic steel tubes for

the detection of surface imperfections

Essais non destructifs des tubes en acier —

Partie 5: Contrôle par magnétoscopie des tubes en acier

ferromagnétique sans soudure et soudés pour la détection des

imperfections de surface

ISO 10893-5:2011(E)

PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.

Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.

ISO copyright office

Case postale 56 • CH-1211 Geneva 20

Tel. + 41 22 749 01 11

Fax + 41 22 749 09 47

E-mail copyright@iso.org

Web www.iso.org

Published in Switzerland

ISO 10893-5:2011(E)

Contents Page

Foreword ............................................................................................................................................................iv

1 Scope......................................................................................................................................................1

2 Normative references............................................................................................................................1

3 Terms and definitions ...........................................................................................................................2

4 General requirements ...........................................................................................................................2

5 Test method ...........................................................................................................................................3

5.1 General ...................................................................................................................................................3

5.2 Testing the tube body ...........................................................................................................................3

5.3 Testing the end/bevel face....................................................................................................................4

6 Evaluation of indications......................................................................................................................4

6.1 General ...................................................................................................................................................4

6.2 Special requirements for evaluation of indications in the pipe body ..............................................5

7 Acceptance ............................................................................................................................................7

7.1 Tube body ..............................................................................................................................................7

7.2 End/bevel face .......................................................................................................................................7

8 Test report..............................................................................................................................................7

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #ISO

摘要：

ISO 10893-5-2011 是关于无缝和焊接钢管无损检测方法的国际标准，具体规定了采用磁粉检测技术对钢管表面缺陷进行检测的技术要求。该标准适用于铁磁性钢管的表面缺陷检测，包括检测设备校准、磁化方法选择、质量等级判定以及验收准则等内容，是钢铁制造、管道工程、压力容器及结构用钢领域确保产品质量和安全性的重要技术依据。遵循 ISO 10893-5-2011 有助于实现检测结果的可比性、提升生产质量管控水平，并满足国际间的质量认证与贸易要求。

展开>> 收起<<

ISO 10893-5-2011.pdf

共14页,预览4页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

ISO 10893-5-2011

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: