MIL-DTL-5015H-2008 AN型圆形螺纹式电连接器通用详细规范

VIP专免

standardshare 2026-04-19 8 3.85MB 75 页 20星币

侵权投诉

MIL-DTL-5015H

AMSC N/A FSC 5935

DETAIL SPECIFICATION

CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE,

GENERAL SPECIFICATION FOR

This specification is approved for use by all Departments and Agencies of the Department

of Defense.

1. SCOPE

1.1 Scope. This specification covers circular threaded electrical connectors with solder or

removable crimp contacts (both front and rear release). These connectors are for use in

electronic, electrical power, and control circuits (see 6.1).

1.2 Classification. Electrical connectors covered by this specification are divided into the

following classes, series, and receptacle styles.

1.2.1 Classes. The classes of electrical connectors are as follows:

Class A - Solid shell solder contact connectors

Class B - Split shell solder contact connectors

Class C - Solder contact connectors for use with pressurized equipment

Class D - Crimp and solder contact connectors for use in high-impact shock conditions

Class DJ - Crimp contact connectors with backshell connector assembly for use in high

impact shock conditions

Comments, suggestions, or questions on this document should be addressed to the Naval Air

Systems Command (Commander, Naval Air Warfare Center Aircraft Division, Code

4L8000B120-3, Highway 547, Lakehurst, NJ 08733-5100) or by e-mail to

michael.sikora@navy.mil. Since contact information can change, you may want to verify the

currency of this address information using the ASSIST online database at

http://assist.daps.dla.mil.

MIL-DTL-5015H

w/AMENDMENT 1

12 August 2008

SUPERSEDING

MIL-DTL-5015H

18 May 2000

INCH-POUND

Downloaded from https://www.everyspec.com

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

MIL-DTL-5015H

w/AMENDMENT 1

Class E - Environment resistant solder contact connectors

Class F - Environment resistant solder contact connectors, with clamp

Class H - Hermetic solder contact connectors

Class K - Crimp and solder firewall connectors

Class L - Fluid resistant crimp contact connectors

Class P - Environment resistant potted solder contact connectors

Class R - Crimp and solder contact connector with grommet seal without clamp

Class U - Fluid resistant crimp contact connectors

Class W - General purpose crimp contact connectors

1.2.2 Series. The series of electrical connectors are as follows:

Series I - Solder contact connectors

Series II - Front release, crimp contact connectors

Series III - Rear release, crimp contact connectors

Series IV - Connector accessories

1.2.3 Receptacle styles. The receptacle styles of electrical connectors are as follows:

Flange (box or wall)

Jam nut

Cable connecting

Solder mounting

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this

specification. This section does not include documents cited in other sections of this

specification or recommended for additional information or as examples. While every effort has

been made to ensure the completeness of this list, document users are cautioned that they must

meet all specified requirements documents cited in sections 3 and 4 of this specification, whether

or not they are listed.

2.2 Government documents.

2.2.1 Specifications and standards. The following specifications and standards form a part

of this document to the extent specified herein. Unless otherwise specified, the issues of these

documents are those listed in the issue of the Department of Defense Index of Specifications and

Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2).

Downloaded from https://www.everyspec.com

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

MIL-DTL-5015H

w/AMENDMENT 1

SPECIFICATIONS

FEDERAL

L-P-410 - Plastic, Polyamide (Nylon), Rigid, Rods, Tubes, Flats,

Molded and Cast Parts.

QQ-S-365 - DELETED

QQ-P-416 - DELETED

DEPARTMENT OF DEFENSE

MIL-S-901 - Shock Tests H.I. (High-Impact) Shipboard Machinery,

Equipment, and Systems, Requirements for.

MIL-C-915 - Cable and Cord, Electrical, for Shipboard Use, General

Specification for.

MIL-H-5606 - Hydraulic Fluid, Petroleum Base; Aircraft, Missile, and

Ordnance. (Inactive for new design)

MIL-S-7742 - Screw Threads, Standard, Optimum Selected Series:

General Specification for. (Inactive for new design)

MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base.

MIL-PRF-8516 - Sealing Compound, Synthetic Rubber, Electric Connectors

and Electric Systems, Chemically Cured.

MIL-W-16878 - Wire, Electrical, Insulated, General Specification for.

MIL-DTL-22520 - Crimping Tools, Terminal, General Specification for.

MIL-W-22759 - DELETED

MIL-PRF-23586 - Sealing Compound (With Accelerator), Silicone Rubber,

Electrical.

MIL-W-25038 - Wire, Electrical, High Temperature, Fire Resistant, and

Flight Critical, General Specification for.

MIL-C-39029 - DELETED

MIL-C-39029/29 - DELETED

MIL-C-39029/30 - DELETED

MIL-C-39029/44 - DELETED

MIL-C-39029/45 - DELETED

MIL-DTL-81381 - Wire, Electric, Polyamide-Insulated, Copper or CopperAlloy.

MIL-I-81969/14 - Installing and Removal Tools, Connector, Electrical Contact,

Type III, Class 2, Composition B.

MIL-I-81969/15 - Installing and Removal Tools, Connector, Electrical Contact,

Type II, Class 2, Composition A.

MIL-I-81969/17 - Installing and Removal Tools, Connectors, Electrical

Contact, Type 1, Composition C.

Downloaded from https://www.everyspec.com

北极星标准文库-高清标准规范分享平台 www.bjxwk.com

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #电连接器

摘要：

本文档详细解读MIL-DTL-5015H-2008标准，该标准为美国军用规范，专门针对AN型圆形螺纹式电连接器的通用技术要求、尺寸、性能及测试方法进行了全面规定。作为航空航天、军事装备及高可靠性工业领域的重要参考，本规范涵盖了从材料选用、密封设计到电气与机械寿命测试的全流程要求。通过阅读本内容，工程师与采购人员可快速掌握最新标准版本（2008年修订版）与旧版的差异，了解如何选择符合军标认证的圆形螺纹耦合连接器，确保设备在极端环境下的电气连接稳定性与互操作性。

展开>> 收起<<

MIL-DTL-5015H-2008 AN型圆形螺纹式电连接器通用详细规范.PDF

共75页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

MIL-DTL-5015H-2008 AN型圆形螺纹式电连接器通用详细规范

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: