沙特阿美公司材料系统规范 32-SAMSS-022 火炬系统部件制造 2018 Manufacture of Components for Flare Systems

VIP专免

标准之家 2026-09-13 6 367.5KB 13 页 25星币

侵权投诉

Previous Issue: 1 January 2018 Next Planned Update: 9 January 2023 Page 1 of 13

Contact: Khaldi, Muhammad M. (khalmm0q) on +966-13-8808084

Saudi Aramco: Company General Use

Materials System Specification

32-SAMSS-022 9 January 2018

Manufacture of Components for Flare Systems

Document Responsibility: Flare Systems Design Standards Committee

Contents

1 Scope ................................................................ 2

2 Conflicts and Deviations .................................... 2

3 References ........................................................ 2

4 Definitions ......................................................... 4

5 Responsibilities ................................................. 6

6 Proposals .......................................................... 6

7 Design ............................................................... 7

8 Materials ........................................................... 9

9 Welding ........................................................... 10

10 Fabrication ...................................................... 12

11 Inspection ........................................................ 13

Revision Summary .................................................. 13

Document Responsibility: Flare Systems Design Standards Committee 32-SAMSS-022

Issue Date: 9 January 2018

Next Planned Update: 9 January 2023 Manufacture of Components for Flare Systems

Page 2 of 13

Saudi Aramco: Company General Use

1 Scope

1.1 This specification covers the minimum mandatory requirements for the design,

fabrication, materials, and inspection of new flare systems and includes: flare

stacks, flare tips, dry gas seals, liquid-seals, and flare knockout drums.

1.2 This specification does not include requirements for incinerators, or equipment

used for the burning of combustibles on ships.

1.3 This specification does not prohibit the use of vendor proprietary designs

required for flare systems. Vendor proprietary designs should be compliant with

this specification unless approved by Saudi Aramco Engineer.

2 Conflicts and Deviations

2.1 Any conflict between this document and other applicable Mandatory Saudi

Aramco Engineering Requirements (MSAERs) shall be addressed in writing to

the EK&RD Coordinator.

2.2 Any deviation from the requirements herein shall follow internal company

procedure SAEP-302, waiver of a Mandatory Saudi Aramco Engineering

Requirements.

3 References

Materials or equipment supplied to this specification shall comply with the latest edition

of the references listed below, unless otherwise noted.

3.1 Saudi Aramco Documents

Saudi Aramco Engineering Procedures

SAEP-302 Waiver of a Mandatory Saudi Aramco Engineering

Requirement

SAEP-405 Flare System Purge Gas Optimization

Saudi Aramco Engineering Standards

SAES-D-001 Welding Requirements for On-Plot Piping

SAES-N-100 Refractory Systems

SAES-N-110 Installation Requirements, Castable Refractories

SAES-W-011 Design Criteria for Pressure Vessels

Document Responsibility: Flare Systems Design Standards Committee 32-SAMSS-022

Issue Date: 9 January 2018

Next Planned Update: 9 January 2023 Manufacture of Components for Flare Systems

Page 3 of 13

Saudi Aramco: Company General Use

Saudi Aramco Materials System Specification

32-SAMSS-004 Manufacture of Pressure Vessels

Saudi Aramco Best Practice

SABP-A-022 Stainless Steel Fabrication, Testing, and Installation

Saudi Aramco Inspection Requirements

Form 175-326700 Flare Systems

Saudi Aramco Forms and Datasheets

SA-7305 Noise Data Sheet

Saudi Aramco-Flare System Forms (herein after referred to as datasheets)

SA-9547 Flare System, Flare Tip Data Sheet

SA-9548 Flare System, General Data Sheet

SA-9549 Flare System, Flare Knockout/Seal Drum Data

Sheet

SA-9561 Flare System-Process Data Sheet

SA-9562 Flare System-Utility Data Sheet

3.2 Industry Codes and Standards

American Petroleum Institute

API STD 601 Metallic Gaskets for Raised-face Pipe Flanges and

Flanged Connections

American Society of Civil Engineers

ASCE 7 Minimum Design Loads for Buildings and Other

Structures

American Society of Mechanical Engineers (Boiler and Pressure Vessel Code)

ASME SEC IX Welding and Brazing Qualifications

ASME B16.5 Pipe Flanges and Flanged Fittings

ASME B16.9 Factory made Wrought Steel Butt Welding Fittings

ASME B16.11 Forged Steel Fittings, Socket Welding, and Threaded

ASME B31.3 Chemical Plant and Petroleum Refinery Piping

ASME B16.47 Large Diameter Steel Flanges NPS 26 through

NPS 60 (Series A)

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #部件 #系统部件 #MS

摘要：

本页提供沙特阿美公司材料系统规范 32-SAMSS-022《火炬系统部件制造》2018版（Manufacture of Components for Flare Systems）的SEO摘要，围绕32-SAMSS-022、火炬系统和制造规范等核心关键词，介绍该标准在火炬系统部件设计、制造、检验、质量控制及供应商合规中的应用，方便工程师、采购人员、制造商和项目管理人员快速获取沙特阿美材料系统规范要求、2018版技术文件信息及相关合规参考。

展开>> 收起<<

沙特阿美公司材料系统规范 32-SAMSS-022 火炬系统部件制造 2018 Manufacture of Components for Flare Systems.pdf

共13页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

沙特阿美公司材料系统规范 32-SAMSS-022 火炬系统部件制造 2018 Manufacture of Components for Flare Systems

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: