沙特阿美公司材料系统规范 26-SAMSS-090 切削、精加工及防护用油 2019 Machining, Finishing and Protection Oils

VIP专免

标准之家 2026-09-13 6 146.92KB 7 页 25星币

侵权投诉

Previous Issue: 16 May 2019 Next Planned Update: 30 November 2022

Revised paragraphs are indicated in the right margin Page 1 of 7

Contact: Aidarous, Mamdouh B. (AIDAROMB) at phone +966-13-880-9718

Materials System Specification

26-SAMSS-090 30 July 2019

Machining, Finishing and Protection Oils

Document Responsibility: Vibration and Lubrication Standards Committee

Contents

1 Scope ................................................................ 2

2 Conflicts and Deviations ................................... 2

3 References ........................................................ 2

4 Penetrating Oils ................................................ 3

5 Rust Preventive ................................................. 3

6 General Purpose Cutting Oil ............................. 3

7 Heavy Duty Cutting Oil ...................................... 4

8 Soluble Oil......................................................... 4

9 Honing Oil ......................................................... 5

10 Synthetic Grinding Fluid .................................... 5

11 Turbine Oil Vapor Space Inhibitor ..................... 6

12 Qualification ...................................................... 6

13 Identification ...................................................... 6

Revision Summary .................................................... 7

Document Responsibility: Vibration and Lubrication Standards Committee 26-SAMSS-090

Issue Date: 30 July 2019

Next Planned Update: 30 November 2022 Machining, Finishing and Protection Oils

Page 2 of 7

1 Scope

This specification describes the requirements for different types of oils to be used for

machining and finishing operation for cooling and lubrication; and as well as protection

purposes.

2 Conflicts and Deviations

2.1 Any conflicts between this document and other applicable Mandatory Saudi

Aramco Engineering Requirements (MSAERs) shall be addressed to the EK&RD

Coordinator.

2.2 Any deviation from the requirements herein shall follow internal company

procedure SAEP-302.

3 References

Material or equipment supplied to this specification shall comply with the latest edition

of the references listed below, unless otherwise noted.

3.1 Saudi Aramco References

Saudi Aramco Engineering Procedure

SAEP-302 Waiver of a Mandatory Saudi Aramco Engineering

Requirement

3.2 Industry Codes and Standards

American Society for Testing and Materials

ASTM D92 Standard Test Method for Flash and Fire Points by

Cleveland Open Cup

ASTM D93 Standard Test Method for Flash Point by Pensky-

Martens Closed Cup Tester

ASTM D130 Standard Test Method for Detection of Copper

Corrosion from Petroleum Products by the

Copper Strip Tarnish Test

ASTM D217 Standard Test Methods for Cone Penetration of

Lubricating Grease

Document Responsibility: Vibration and Lubrication Standards Committee 26-SAMSS-090

Issue Date: 30 July 2019

Next Planned Update: 30 November 2022 Machining, Finishing and Protection Oils

Page 3 of 7

4 Penetrating Oils

4.1 Scope

This specification describes a low viscosity product suitable for brush or spray

application and is used to aid in loosening nuts, studs, bolts, etc. In addition to

its penetrating ability, it is also a good rust preventative and lubricant.

4.2 Requirements

This product shall be made from high viscosity mineral oil cut back with

solvents and a fatty oil type additive to promote penetration. It shall have

approximately the following characteristics:

ISO Viscosity Grade : 7

Flash Point, °C (ASTM D92) : 65 minimum

5 Rust Preventive

5.1 Scope

This specification describes the requirements of a soft film rust preventive for

the protection of iron and steel including machine parts, pipe joints, flanges,

valves, etc. This product may be applied, unheated, by brush, spray, or dip.

5.2 Requirements

The basic material of this product is approximately of NLGI-5 consistency and

contains a thinner to facilitate application. This product, on application shall be

resistant to flow in ambient temperatures up to 60°C and shall have

approximately the following characteristics:

Penetration (ASTM D217), Unworked at 25°C : 250

Diluent, mass % : 20

NLGI-consistency before solvent evaporation : 2

NLGI-consistency after solvent evaporation : 5

6 General Purpose Cutting Oil

6.1 Scope

This specification describes the requirements of general purpose non-corrosive,

transparent type cutting oil for the machining of metals and alloys where an

active sulphur type oil might cause staining or other undesirable effects. It can

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #MS #材料 #沙特

摘要：

本页面提供沙特阿美公司材料系统规范 26-SAMSS-090《切削、精加工及防护用油》2019版（Machining, Finishing and Protection Oils）的SEO优化内容，详细介绍该标准对切削油、精加工油和防护油的技术要求、性能指标、检验方法、包装标识、储存及供应商合规要点。适用于石油天然气、炼化、机械加工和工业制造项目的材料选型、采购验收与质量审核。用户可通过本页了解 26-SAMSS-090 标准适用范围、版本更新、沙特阿美 SAMSS 认证要求及常见问题，快速获取

展开>> 收起<<

沙特阿美公司材料系统规范 26-SAMSS-090 切削、精加工及防护用油 2019 Machining, Finishing and Protection Oils.pdf

共7页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

沙特阿美公司材料系统规范 26-SAMSS-090 切削、精加工及防护用油 2019 Machining, Finishing and Protection Oils

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: