API SPEC 15HR-2016 (R2026) 4TH ED (E1) (E2) 高压玻璃纤维管线管

VIP免费

那山那人那狗 2026-09-13 8 727.07KB 39 页 26星币

侵权投诉

High-pressure Fiberglass Line Pipe

API SPECIFICATION 15HR

FOURTH EDITION, FEBRUARY 2016

API MONOGRAM PROGRAM EFFECTIVE DATE: AUGUST 1, 2016

ERRATA 1, AUGUST 2016

ERRATA 2, JANUARY 2021

REAFFIRMED, APRIL 2026

Special Notes

API publications necessarily address problems of a general nature. With respect to particular circumstances, local,

state, and federal laws and regulations should be reviewed. The use of API publications is voluntary. In some cases,

third parties or authorities having jurisdiction may choose to incorporate API standards by reference and may

mandate compliance.

Neither API nor any of API’s employees, subcontractors, consultants, committees, or other assignees make any

warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the

information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any

information or process disclosed in this publication. Neither API nor any of API's employees, subcontractors,

consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.

API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the

accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or

guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or

damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may

conflict.

API publications are published to facilitate the broad availability of proven, sound engineering and operating

practices. These publications are not intended to obviate the need for applying sound engineering judgment

regarding when and where these publications should be utilized. The formulation and publication of API publications

is not intended in any way to inhibit anyone from using any other practices.

Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard

is solely responsible for complying with all the applicable requirements of that standard. API does not represent,

warrant, or guarantee that such products do in fact conform to the applicable API standard.

Classified areas may vary depending on the location, conditions, equipment, and substances involved in any given

situation. Users of this specification should consult with the appropriate authorities having jurisdiction.

Users of this specification should not rely exclusively on the information contained in this document. Sound business,

scientific, engineering, and safety judgment should be used in employing the information contained herein.

electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the

Publisher, API Publishing Services, 200 Massachusetts Avenue, NW, Suite 1100, Washington, DC 20001.

Foreword

This specification is under the jurisdiction of the American Petroleum Institute Subcommittee on Fiberglass and

Plastic Tubulars. The purpose of this specification is to provide standards for high-pressure fiberglass line pipe and

fittings for use in conveying produced fluids including oil, gas, nonpotable water, and mixtures thereof in the oil and

gas producing industries.

Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the

manufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anything

contained in the publication be construed as insuring anyone against liability for infringement of letters patent.

The verbal forms used to express the provisions in this recommended practice are as follows:

— the term “shall” denotes a minimum requirement in order to conform to the recommended practice;

— the term “should” denotes a recommendation or that which is advised but not required in order to conform to the

recommended practice;

— the term “may” is used to express permission or a provision that is optional; and

— the term “can” is used to express possibility or capability.

This document was produced under API standardization procedures that ensure appropriate notification and

participation in the developmental process and is designated as an API standard. Questions concerning the

interpretation of the content of this publication or comments and questions concerning the procedures under which

this publication was developed should be directed in writing to the Director of Standards, American Petroleum

Institute, 200 Massachusetts Avenue, NW, Suite 1100, Washington, DC 20001. Requests for permission to reproduce

or translate all or any part of the material published herein should also be addressed to the director.

Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time

extension of up to two years may be added to this review cycle. Status of the publication can be ascertained from the

API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published

annually by API, 200 Massachusetts Avenue, NW, Suite 1100, Washington, DC 20001.

Suggested revisions are invited and should be submitted to the Standards Department, API, 200 Massachusetts

Avenue, NW, Suite 1100, Washington, DC 20001, standards@api.org.

Attention Users of this Publication: This edition of API Specification 15HR supersedes the Third Edition and includes

items approved by letter ballot. Those ballot approved items (substantive changes) are indicated with gray shading

and red font, but API makes no warranty as to the accuracy of such notations. Non-substantive changes will not be

indicated. Portions of this publication have been changed from the previous edition. In some cases the changes are

significant, while in other cases the changes reflect minor editorial adjustments in order to conform to current API

styling. Since the document was significantly reformatted from the previous edition, no attempt was made to indicate

the location of changes with bar notations.

iii

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

亲，本站95%以上的标准规范都面向会员免费，办理VIP会员下载更省钱，平均每篇不到2元

立即下载 VIP免费下载

标签： #高压 #管 #纤维

摘要：

API SPEC 15HR-2016 (R2026) 4TH ED (E1) (E2) 高压玻璃纤维管线管是石油天然气行业高压玻璃纤维增强热固性树脂管线管的重要标准规范，涵盖产品范围、材料要求、尺寸与公差、性能指标、试验方法、检验规则、标识、包装、运输和验收等内容。该第四版标准于2016年发布，并于2026年重新确认，适用于高压玻璃纤维管线管的设计、制造、采购、检验和合规管理。通过本页面可获取该标准的技术信息、版本状态、适用范围和SEO相关关键词，帮助工程师、采购人员和检测机构快速了解API S

展开>> 收起<<

API SPEC 15HR-2016 (R2026) 4TH ED (E1) (E2) 高压玻璃纤维管线管.pdf

共39页,预览3页

还剩页未读，继续阅读

声明：本文档系会员上传，若文档所含内容侵犯了您的版权或隐私，请立即通知，我们立即给予侵权申诉删除！

API SPEC 15HR-2016 (R2026) 4TH ED (E1) (E2) 高压玻璃纤维管线管

相关推荐

开通VIP享超值会员特权

相关内容

热门标签

举报选择: